controller/ata/sil3xxx.c

/*
 * CDDL HEADER START
 *
 * The contents of this file are subject to the terms of the
 * Common Development and Distribution License (the "License").
 * You may not use this file except in compliance with the License.
 *
 * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
 * or http://www.opensolaris.org/os/licensing.
 * See the License for the specific language governing permissions
 * and limitations under the License.
 *
 * When distributing Covered Code, include this CDDL HEADER in each
 * file and include the License file at usr/src/OPENSOLARIS.LICENSE.
 * If applicable, add the following below this CDDL HEADER, with the
 * fields enclosed by brackets "[]" replaced with your own identifying
 * information: Portions Copyright [yyyy] [name of copyright owner]
 *
 * CDDL HEADER END
 */

/*
 * Copyright 2004 Sun Microsystems, Inc.  All rights reserved.
 * Use is subject to license terms.
 */
/*
 * Silicon Image 3XXX controller specific processing
 *
 * This file may be expanded to take advantage of Silicon Image
 * additional features (if applicable to specific controller model):
 * 1. Virtual DMA operation
 * 2. Concurrent all-channel DMA
 * 3. Large Block Transfers
 * 4. Watchdog Timer
 * 5. Power Management
 * 6. Hot Plug Support
 */

#pragma ident   "%Z%%M% %I% %E% SMI"

#include "ata_common.h"
#include "sil3xxx.h"
#include <sys/pci.h>

int fifocntctl[] = {FIFO_CNTCTL_0, FIFO_CNTCTL_1, FIFO_CNTCTL_2, FIFO_CNTCTL_3};
int sfiscfg[] = {SFISCFG_0, SFISCFG_1, SFISCFG_2, SFISCFG_3};

/*
 * Controller specific initialization
 */
uint_t
sil3xxx_init_controller(dev_info_t *dip,
    /* LINTED */
    ushort_t vendor_id, ushort_t device_id)
{
    ddi_acc_handle_t  pci_conf_handle; /* pci config space handle */
    uint8_t cache_lnsz, frrc = 0;
    uint32_t fifo_cnt_ctl;
    int ports, i;

#ifdef  DEBUG
    /* LINTED */
    ushort_t sfiscfg_val;
#endif

    /*
     * Sil3114, Sil3512, Sil3112
     * We want to perform this initialization only once per entire
     * pciide controller (all channels)
     */
    if (ddi_prop_exists(DDI_DEV_T_ANY, ddi_get_parent(dip),
        DDI_PROP_DONTPASS, "sil3xxx-initialized")) {
        return (TRUE);
    }

    if (pci_config_setup(ddi_get_parent(dip), &pci_conf_handle) !=
        DDI_SUCCESS) {
        cmn_err(CE_WARN,
            "sil3xxx_init_controller: Can't do pci_config_setup\n");
        return (FALSE);
    }

    /*
     * Sil3114/3512/3112 incorrectly change between MR and back to
     * MRM for same transaction, which violates the PCI spec and can
     * lead to incorrect data reads.  The workaround
     * is to set bits 2:0 in the FIFO count and control register so
     * that its value, a multiple of 32 bytes starting at 32, not 0,
     * is greater or equal to the cacheline size, a multiple of 4
     * bytes.  This will prevent any reads until the FIFO free space
     * is greater than a cacheline size, ensuring only MRM is issued.
     */

    cache_lnsz = pci_config_get8(pci_conf_handle, PCI_CONF_CACHE_LINESZ);

    /*
     * The cache line is specified in 32-bit words, so multiply by 4
     * to get bytes.  Then divide by 32 bytes, the granularity of the
     * FIFO control bits 2:0.  Add 1 if there is any remainder to
     * account for a partial 32-byte block, then subtract 1 since for
     * FIFO controls bits 2:0, 0 corresponds to 32, 1 corresponds to
     * 64, and so on.  The calculation is expanded for clarity.
     */
    if (cache_lnsz != 0) {
        frrc = (cache_lnsz * 4 / 32) +
            (((cache_lnsz * 4) % 32) ? 1 : 0) - 1;
    }

    if (device_id == SIL3114_DEVICE_ID) {
        ports = 4;
    } else {
        ports = 2;
    }

    /*
     * The following BAR5 registers are accessed via an indirect register
     * in the PCI configuration space rather than mapping BAR5.
     */
    for (i = 0; i < ports; i++) {
        GET_BAR5_INDIRECT(pci_conf_handle, fifocntctl[i],
            fifo_cnt_ctl);
        fifo_cnt_ctl = (fifo_cnt_ctl & ~0x7) | (frrc & 0x7);
        PUT_BAR5_INDIRECT(pci_conf_handle, fifocntctl[i],
            fifo_cnt_ctl);
        /*
         * Correct default setting for FIS0cfg
         */
#ifdef  DEBUG
        GET_BAR5_INDIRECT(pci_conf_handle, sfiscfg[i],
            sfiscfg_val);
        ADBG_WARN(("sil3xxx_init_controller: old val SFISCfg "
            "ch%d: %x\n", i, sfiscfg_val));
#endif
        PUT_BAR5_INDIRECT(pci_conf_handle, sfiscfg[i],
            SFISCFG_ERRATA);
#ifdef  DEBUG
        GET_BAR5_INDIRECT(pci_conf_handle, sfiscfg[i],
            sfiscfg_val);
        ADBG_WARN(("sil3xxx_init_controller: new val SFISCfg "
            "ch%d: %x\n", i, sfiscfg_val));
#endif
    }

    /* Now tear down the pci config setup */
    pci_config_teardown(&pci_conf_handle);

    /* Create property indicating that initialization was done */
    (void) ddi_prop_update_int(DDI_DEV_T_NONE, ddi_get_parent(dip),
        "sil3xxx-initialized", 1);

    return (TRUE);
}