#
# CDDL HEADER START
#
# The contents of this file are subject to the terms of the
# Common Development and Distribution License (the "License").
# You may not use this file except in compliance with the License.
#
# You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
# See the License for the specific language governing permissions
# and limitations under the License.
#
# When distributing Covered Code, include this CDDL HEADER in each
# file and include the License file at usr/src/OPENSOLARIS.LICENSE.
# If applicable, add the following below this CDDL HEADER, with the
# fields enclosed by brackets "[]" replaced with your own identifying
# information: Portions Copyright [yyyy] [name of copyright owner]
#
# CDDL HEADER END
#
#
# Copyright(c) 2007-2010 Intel Corporation. All rights reserved.
#
#
#
#
# Driver.conf file for Intel 1Gb ethernet driver (igb)
#
# -------------------- Link Configuration --------------------
# The parameters of link configuration:
#
# adv_autoneg_cap
# Advertise capability of auto-negotiation.
# Allowed values: 0, 1
# Default value: 1
#
# adv_1000fdx_cap
# Advertise capability of 1000Mbps full duplex
# Allowed values: 0, 1
# Default value: 1
#
# adv_100fdx_cap
# Advertise capability of 100Mbps full duplex
# Allowed values: 0, 1
# Default value: 1
#
# adv_100hdx_cap
# Advertise capability of 100Mbps half duplex
# Allowed values: 0, 1
# Default value: 1
#
# adv_10fdx_cap
# Advertise capability of 10Mbps full duplex
# Allowed values: 0, 1
# Default value: 1
#
# adv_10hdx_cap
# Advertise capability of 10Mbps half duplex
# Allowed values: 0, 1
# Default value: 1
#
# There are two methods to configure the link:
# autonegotiation or forced link
#
# The parameter "adv_autoneg_cap" is used to enable autonegotiation or disable
# it (forced link mode).
#
# If autonegotiation is enabled (the default mode), all the "adv_*_cap"
# parameters control which capabilities are advertised to the partner. The
# default is to advertise all the capabilities that the hardware supports.
# The advertised capabilities can also be restricted to a subset. It is not
# possible to advertise a capability that the hardware does not support.
#
# The autonegotiation process will then automatically select the fastest speed/
# duplex mode supported by both partners.
#
# determined by the first link capability that is enabled, in highest-to-lowest
#
# For example, if adv_1000fdx_cap is enabled, all other values will be ignored;
# to force 10hdx mode, all the faster modes must be explicitly disabled.
#
# Note:
# 1. 1000M half duplex is not supported with igb.
# 2. 1000M speed is not supported with the forced link mode (the value of
# adv_1000fdx_cap will be ignored).
# 3. The forced link mode may result in a non-working link or a half duplex
# link. If forced link mode is used, both the partners should be forced to
#
# adv_autoneg_cap = 1;
# adv_1000fdx_cap = 1;
# adv_100fdx_cap = 1;
# adv_100hdx_cap = 1;
# adv_10fdx_cap = 1;
# adv_10hdx_cap = 1;
#
# -------------------- Jumbo Frame --------------------
# default_mtu
# The size of the default MTU (payload without the ethernet header)
# Allowed values: 1500 - 9000
# Default value: 1500
#
# default_mtu = 1500;
#
# -------------------- Flow Control --------------------
# flow_control
# Ethernet flow control
# Allowed values: 0 - Disable
# 1 - Receive only
# 2 - Transmit only
# 3 - Receive and transmit
# 4 - Use NVROM-programmed factory default setting
# default value: 3
#
# flow_control = 3;
#
#
# tx_ring_size
# The number of the transmit descriptors per transmit queue
# Allowed values: 64 - 4096
# Default value: 512
#
# rx_ring_size
# The number of the receive descriptors per receive queue
# Allowed values: 64 - 4096
# Default value: 512
#
# mr_enable
# Enable multiple rx queues and tx queues
# Allowed values: 0, 1
# Default value: 0
#
# rx_group_number
# The number of the receive ring groups
# Allowed values: 1 - 4
# Default value: 1
#
# Note: If the specified values of the rx_group_number are not supported by
# hardware, the rx_group_number will be downgrade to an acceptable value.
#
# -------- How to set parameters for a particular interface ---------
# The example below shows how to locate the device path and set a parameter
# for a particular igb interface. (Using flow_control as an example)
#
# Use the following command to find out the device paths for igb,
# more /etc/path_to_inst | grep igb
#
# For example, if you see,
#
# name = "pciex8086,10a7" parent = "/pci@0,0/pci10de,5d@d" unit-address = "0"
# flow_control = 1;
# name = "pciex8086,10a7" parent = "/pci@0,0/pci10de,5d@d" unit-address = "0,1"
# flow_control = 3;