io/bge/bge_hw.h

	bge_hw.h revision da14cebe459d3275048785f25bd869cb09b5307f
/*
 * CDDL HEADER START
 *
 * The contents of this file are subject to the terms of the
 * Common Development and Distribution License (the "License").
 * You may not use this file except in compliance with the License.
 *
 * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
 * or http://www.opensolaris.org/os/licensing.
 * See the License for the specific language governing permissions
 * and limitations under the License.
 *
 * When distributing Covered Code, include this CDDL HEADER in each
 * file and include the License file at usr/src/OPENSOLARIS.LICENSE.
 * If applicable, add the following below this CDDL HEADER, with the
 * fields enclosed by brackets "[]" replaced with your own identifying
 * information: Portions Copyright [yyyy] [name of copyright owner]
 *
 * CDDL HEADER END
 */

/*
 * Copyright 2008 Sun Microsystems, Inc.  All rights reserved.
 * Use is subject to license terms.
 */

#ifndef _BGE_HW_H
#define _BGE_HW_H

#ifdef __cplusplus
extern "C" {
#endif

#include <sys/types.h>


/*
 * First section:
 *  Identification of the various Broadcom chips
 *
 * Note: the various ID values are *not* all unique ;-(
 *
 * Note: the presence of an ID here does *not* imply that the chip is
 * supported.  At this time, only the 5703C, 5704C, and 5704S devices
 * used on the motherboards of certain Sun products are supported.
 *
 * Note: the revision-id values in the PCI revision ID register are
 * *NOT* guaranteed correct.  Use the chip ID from the MHCR instead.
 */

#define VENDOR_ID_BROADCOM      0x14e4
#define VENDOR_ID_SUN           0x108e

#define DEVICE_ID_5700          0x1644
#define DEVICE_ID_5700x         0x0003
#define DEVICE_ID_5701          0x1645
#define DEVICE_ID_5702          0x16a6
#define DEVICE_ID_5702fe        0x164d
#define DEVICE_ID_5703C         0x1647
#define DEVICE_ID_5703S         0x16a7
#define DEVICE_ID_5703          0x16c7
#define DEVICE_ID_5704C         0x1648
#define DEVICE_ID_5704S         0x16a8
#define DEVICE_ID_5704          0x1649
#define DEVICE_ID_5705C         0x1653
#define DEVICE_ID_5705_2        0x1654
#define DEVICE_ID_5705M         0x165d
#define DEVICE_ID_5705MA3       0x165e
#define DEVICE_ID_5705F         0x166e
#define DEVICE_ID_5706          0x164a
#define DEVICE_ID_5780          0x166a
#define DEVICE_ID_5782          0x1696
#define DEVICE_ID_5787          0x169b
#define DEVICE_ID_5787M         0x1693
#define DEVICE_ID_5788          0x169c
#define DEVICE_ID_5789          0x169d
#define DEVICE_ID_5751          0x1677
#define DEVICE_ID_5751M         0x167d
#define DEVICE_ID_5752          0x1600
#define DEVICE_ID_5752M         0x1601
#define DEVICE_ID_5753          0x16fd
#define DEVICE_ID_5754          0x167a
#define DEVICE_ID_5755          0x167b
#define DEVICE_ID_5755M         0x1673
#define DEVICE_ID_5756M         0x1674
#define DEVICE_ID_5721          0x1659
#define DEVICE_ID_5722          0x165a
#define DEVICE_ID_5714C         0x1668
#define DEVICE_ID_5714S         0x1669
#define DEVICE_ID_5715C         0x1678
#define DEVICE_ID_5715S         0x1679
#define DEVICE_ID_5906          0x1712
#define DEVICE_ID_5906M         0x1713

#define REVISION_ID_5700_B0     0x10
#define REVISION_ID_5700_B2     0x12
#define REVISION_ID_5700_B3     0x13
#define REVISION_ID_5700_C0     0x20
#define REVISION_ID_5700_C1     0x21
#define REVISION_ID_5700_C2     0x22

#define REVISION_ID_5701_A0     0x08
#define REVISION_ID_5701_A2     0x12
#define REVISION_ID_5701_A3     0x15

#define REVISION_ID_5702_A0     0x00

#define REVISION_ID_5703_A0     0x00
#define REVISION_ID_5703_A1     0x01
#define REVISION_ID_5703_A2     0x02

#define REVISION_ID_5704_A0     0x00
#define REVISION_ID_5704_A1     0x01
#define REVISION_ID_5704_A2     0x02
#define REVISION_ID_5704_A3     0x03
#define REVISION_ID_5704_B0     0x10

#define REVISION_ID_5705_A0     0x00
#define REVISION_ID_5705_A1     0x01
#define REVISION_ID_5705_A2     0x02
#define REVISION_ID_5705_A3     0x03

#define REVISION_ID_5721_A0     0x00
#define REVISION_ID_5721_A1     0x01

#define REVISION_ID_5751_A0     0x00
#define REVISION_ID_5751_A1     0x01

#define REVISION_ID_5714_A0     0x00
#define REVISION_ID_5714_A1     0x01
#define REVISION_ID_5714_A2     0xA2
#define REVISION_ID_5714_A3     0xA3

#define REVISION_ID_5715_A0     0x00
#define REVISION_ID_5715_A1     0x01
#define REVISION_ID_5715_A2     0xA2

#define REVISION_ID_5715S_A0        0x00
#define REVISION_ID_5715S_A1        0x01

#define REVISION_ID_5754_A0     0x00
#define REVISION_ID_5754_A1     0x01

#define DEVICE_5704_SERIES_CHIPSETS(bgep)\
        ((bgep->chipid.device == DEVICE_ID_5700) ||\
        (bgep->chipid.device == DEVICE_ID_5701) ||\
        (bgep->chipid.device == DEVICE_ID_5702) ||\
        (bgep->chipid.device == DEVICE_ID_5702fe)||\
        (bgep->chipid.device == DEVICE_ID_5703C) ||\
        (bgep->chipid.device == DEVICE_ID_5703S) ||\
        (bgep->chipid.device == DEVICE_ID_5703) ||\
        (bgep->chipid.device == DEVICE_ID_5704C) ||\
        (bgep->chipid.device == DEVICE_ID_5704S) ||\
        (bgep->chipid.device == DEVICE_ID_5704))

#define DEVICE_5702_SERIES_CHIPSETS(bgep) \
        ((bgep->chipid.device == DEVICE_ID_5702) ||\
        (bgep->chipid.device == DEVICE_ID_5702fe))

#define DEVICE_5705_SERIES_CHIPSETS(bgep) \
        ((bgep->chipid.device == DEVICE_ID_5705C) ||\
        (bgep->chipid.device == DEVICE_ID_5705M) ||\
        (bgep->chipid.device == DEVICE_ID_5705MA3) ||\
        (bgep->chipid.device == DEVICE_ID_5705F) ||\
        (bgep->chipid.device == DEVICE_ID_5780) ||\
        (bgep->chipid.device == DEVICE_ID_5782) ||\
        (bgep->chipid.device == DEVICE_ID_5788) ||\
        (bgep->chipid.device == DEVICE_ID_5705_2) ||\
        (bgep->chipid.device == DEVICE_ID_5754) ||\
        (bgep->chipid.device == DEVICE_ID_5755) ||\
        (bgep->chipid.device == DEVICE_ID_5756M) ||\
        (bgep->chipid.device == DEVICE_ID_5753))

#define DEVICE_5721_SERIES_CHIPSETS(bgep) \
        ((bgep->chipid.device == DEVICE_ID_5721) ||\
        (bgep->chipid.device == DEVICE_ID_5751) ||\
        (bgep->chipid.device == DEVICE_ID_5751M) ||\
        (bgep->chipid.device == DEVICE_ID_5752) ||\
        (bgep->chipid.device == DEVICE_ID_5752M) ||\
        (bgep->chipid.device == DEVICE_ID_5789))

#define DEVICE_5714_SERIES_CHIPSETS(bgep) \
        ((bgep->chipid.device == DEVICE_ID_5714C) ||\
        (bgep->chipid.device == DEVICE_ID_5714S) ||\
        (bgep->chipid.device == DEVICE_ID_5715C) ||\
        (bgep->chipid.device == DEVICE_ID_5715S))

#define DEVICE_5906_SERIES_CHIPSETS(bgep) \
        ((bgep->chipid.device == DEVICE_ID_5906) ||\
        (bgep->chipid.device == DEVICE_ID_5906M))

/*
 * Second section:
 *  Offsets of important registers & definitions for bits therein
 */

/*
 * PCI-X registers & bits
 */
#define PCIX_CONF_COMM          0x42
#define PCIX_COMM_RELAXED       0x0002

/*
 * Miscellaneous Host Control Register, in PCI config space
 */
#define PCI_CONF_BGE_MHCR       0x68
#define MHCR_CHIP_REV_MASK      0xffff0000
#define MHCR_ENABLE_TAGGED_STATUS_MODE  0x00000200
#define MHCR_MASK_INTERRUPT_MODE    0x00000100
#define MHCR_ENABLE_INDIRECT_ACCESS 0x00000080
#define MHCR_ENABLE_REGISTER_WORD_SWAP  0x00000040
#define MHCR_ENABLE_CLOCK_CONTROL_WRITE 0x00000020
#define MHCR_ENABLE_PCI_STATE_WRITE 0x00000010
#define MHCR_ENABLE_ENDIAN_WORD_SWAP    0x00000008
#define MHCR_ENABLE_ENDIAN_BYTE_SWAP    0x00000004
#define MHCR_MASK_PCI_INT_OUTPUT    0x00000002
#define MHCR_CLEAR_INTERRUPT_INTA   0x00000001

#define MHCR_CHIP_REV_5700_B0       0x71000000
#define MHCR_CHIP_REV_5700_B2       0x71020000
#define MHCR_CHIP_REV_5700_B3       0x71030000
#define MHCR_CHIP_REV_5700_C0       0x72000000
#define MHCR_CHIP_REV_5700_C1       0x72010000
#define MHCR_CHIP_REV_5700_C2       0x72020000

#define MHCR_CHIP_REV_5701_A0       0x00000000
#define MHCR_CHIP_REV_5701_A2       0x00020000
#define MHCR_CHIP_REV_5701_A3       0x00030000
#define MHCR_CHIP_REV_5701_A5       0x01050000

#define MHCR_CHIP_REV_5702_A0       0x10000000
#define MHCR_CHIP_REV_5702_A1       0x10010000
#define MHCR_CHIP_REV_5702_A2       0x10020000

#define MHCR_CHIP_REV_5703_A0       0x10000000
#define MHCR_CHIP_REV_5703_A1       0x10010000
#define MHCR_CHIP_REV_5703_A2       0x10020000
#define MHCR_CHIP_REV_5703_B0       0x11000000
#define MHCR_CHIP_REV_5703_B1       0x11010000

#define MHCR_CHIP_REV_5704_A0       0x20000000
#define MHCR_CHIP_REV_5704_A1       0x20010000
#define MHCR_CHIP_REV_5704_A2       0x20020000
#define MHCR_CHIP_REV_5704_A3       0x20030000
#define MHCR_CHIP_REV_5704_B0       0x21000000

#define MHCR_CHIP_REV_5705_A0       0x30000000
#define MHCR_CHIP_REV_5705_A1       0x30010000
#define MHCR_CHIP_REV_5705_A2       0x30020000
#define MHCR_CHIP_REV_5705_A3       0x30030000
#define MHCR_CHIP_REV_5705_A5       0x30050000

#define MHCR_CHIP_REV_5782_A0       0x30030000
#define MHCR_CHIP_REV_5782_A1       0x30030088

#define MHCR_CHIP_REV_5788_A1       0x30050000

#define MHCR_CHIP_REV_5751_A0       0x40000000
#define MHCR_CHIP_REV_5751_A1       0x40010000

#define MHCR_CHIP_REV_5721_A0       0x41000000
#define MHCR_CHIP_REV_5721_A1       0x41010000

#define MHCR_CHIP_REV_5714_A0       0x50000000
#define MHCR_CHIP_REV_5714_A1       0x90010000

#define MHCR_CHIP_REV_5715_A0       0x50000000
#define MHCR_CHIP_REV_5715_A1       0x90010000

#define MHCR_CHIP_REV_5715S_A0      0x50000000
#define MHCR_CHIP_REV_5715S_A1      0x90010000

#define MHCR_CHIP_REV_5754_A0       0xb0000000
#define MHCR_CHIP_REV_5754_A1       0xb0010000

#define MHCR_CHIP_REV_5787_A0       0xb0000000
#define MHCR_CHIP_REV_5787_A1       0xb0010000
#define MHCR_CHIP_REV_5787_A2       0xb0020000

#define MHCR_CHIP_REV_5755_A0       0xa0000000
#define MHCR_CHIP_REV_5755_A1       0xa0010000

#define MHCR_CHIP_REV_5906_A0       0xc0000000
#define MHCR_CHIP_REV_5906_A1       0xc0010000
#define MHCR_CHIP_REV_5906_A2       0xc0020000

#define MHCR_CHIP_ASIC_REV(ChipRevId)   ((ChipRevId) & 0xf0000000)
#define MHCR_CHIP_ASIC_REV_5700     (0x7 << 28)
#define MHCR_CHIP_ASIC_REV_5701     (0x0 << 28)
#define MHCR_CHIP_ASIC_REV_5703     (0x1 << 28)
#define MHCR_CHIP_ASIC_REV_5704     (0x2 << 28)
#define MHCR_CHIP_ASIC_REV_5705     (0x3 << 28)
#define MHCR_CHIP_ASIC_REV_5721_5751    (0x4 << 28)
#define MHCR_CHIP_ASIC_REV_5714     (0x5 << 28)
#define MHCR_CHIP_ASIC_REV_5752     (0x6 << 28)
#define MHCR_CHIP_ASIC_REV_5754     (0xb << 28)
#define MHCR_CHIP_ASIC_REV_5787     ((uint32_t)0xb << 28)
#define MHCR_CHIP_ASIC_REV_5755     ((uint32_t)0xa << 28)
#define MHCR_CHIP_ASIC_REV_5715     ((uint32_t)0x9 << 28)
#define MHCR_CHIP_ASIC_REV_5906     ((uint32_t)0xc << 28)


/*
 * PCI DMA read/write Control Register, in PCI config space
 *
 * Note that several fields previously defined here have been deleted
 * as they are not implemented in the 5703/4.
 *
 * Note: the value of this register is critical.  It is possible to
 * cause various unpleasant effects (DTOs, transaction deadlock, etc)
 * by programming the wrong value.  The value #defined below has been
 * tested and shown to avoid all known problems.  If it is to be changed,
 * correct operation must be reverified on all supported platforms.
 *
 * In particular, we set both watermark fields to 2xCacheLineSize (128)
 * bytes and DMA_MIN_BEATS to 0 in order to avoid unfortunate interactions
 * with Tomatillo's internal pipelines, that otherwise result in stalls,
 * repeated retries, and DTOs.
 */
#define PCI_CONF_BGE_PDRWCR     0x6c
#define PDRWCR_RWCMD_MASK       0xFF000000
#define PDRWCR_PCIX32_BUGFIX_MASK   0x00800000
#define PDRWCR_WRITE_WATERMARK_MASK 0x00380000
#define PDRWCR_READ_WATERMARK_MASK  0x00070000
#define PDRWCR_CONCURRENCY_MASK     0x0000c000
#define PDRWCR_5704_FLOP_ON_RETRY   0x00008000
#define PDRWCR_ONE_DMA_AT_ONCE      0x00004000
#define PDRWCR_MIN_BEAT_MASK        0x000000ff

/*
 * These are the actual values to be put into the fields shown above
 */
#define PDRWCR_RWCMDS           0x76000000  /* MW and MR    */
#define PDRWCR_DMA_WRITE_WATERMARK  0x00180000  /* 011 => 128   */
#define PDRWCR_DMA_READ_WATERMARK   0x00030000  /* 011 => 128   */
#define PDRWCR_MIN_BEATS        0x00000000

#define PDRWCR_VAR_DEFAULT      0x761b0000
#define PDRWCR_VAR_5721         0x76180000
#define PDRWCR_VAR_5714         0x76148000  /* OR of above  */
#define PDRWCR_VAR_5715         0x76144000  /* OR of above  */

/*
 * PCI State Register, in PCI config space
 *
 * Note: this register is read-only unless the ENABLE_PCI_STATE_WRITE bit
 * is set in the MHCR, EXCEPT for the RETRY_SAME_DMA bit which is always RW
 */
#define PCI_CONF_BGE_PCISTATE       0x70
#define PCISTATE_RETRY_SAME_DMA     0x00002000
#define PCISTATE_FLAT_VIEW      0x00000100
#define PCISTATE_EXT_ROM_RETRY      0x00000040
#define PCISTATE_EXT_ROM_ENABLE     0x00000020
#define PCISTATE_BUS_IS_32_BIT      0x00000010
#define PCISTATE_BUS_IS_FAST        0x00000008
#define PCISTATE_BUS_IS_PCI     0x00000004
#define PCISTATE_INTA_STATE     0x00000002
#define PCISTATE_FORCE_RESET        0x00000001

/*
 * PCI Clock Control Register, in PCI config space
 */
#define PCI_CONF_BGE_CLKCTL     0x74
#define CLKCTL_PCIE_PLP_DISABLE     0x80000000
#define CLKCTL_PCIE_DLP_DISABLE     0x40000000
#define CLKCTL_PCIE_TLP_DISABLE     0x20000000
#define CLKCTL_PCI_READ_TOO_LONG_FIX    0x04000000
#define CLKCTL_PCI_WRITE_TOO_LONG_FIX   0x02000000
#define CLKCTL_PCIE_A0_FIX      0x00101000

/*
 * Dual MAC Control Register, in PCI config space
 */
#define PCI_CONF_BGE_DUAL_MAC_CONTROL   0xB8
#define DUALMAC_CHANNEL_CONTROL_MASK    0x00000003  /* RW   */
#define DUALMAC_CHANNEL_ID_MASK     0x00000004  /* RO   */

/*
 * Register Indirect Access Address Register, 0x78 in PCI config
 * space.  Once this is set, accesses to the Register Indirect
 * Access Data Register (0x80) refer to the register whose address
 * is given by *this* register.  This allows access to all the
 * operating registers, while using only config space accesses.
 *
 * Note that the address written to the RIIAR should lie in one
 * of the following ranges:
 *  0x00000000 <= address < 0x00008000 (regular registers)
 *  0x00030000 <= address < 0x00034000 (RxRISC scratchpad)
 *  0x00034000 <= address < 0x00038000 (TxRISC scratchpad)
 *  0x00038000 <= address < 0x00038800 (RxRISC ROM)
 */
#define PCI_CONF_BGE_RIAAR      0x78
#define PCI_CONF_BGE_RIADR      0x80

#define RIAAR_REGISTER_MIN      0x00000000
#define RIAAR_REGISTER_MAX      0x00008000
#define RIAAR_RX_SCRATCH_MIN        0x00030000
#define RIAAR_RX_SCRATCH_MAX        0x00034000
#define RIAAR_TX_SCRATCH_MIN        0x00034000
#define RIAAR_TX_SCRATCH_MAX        0x00038000
#define RIAAR_RXROM_MIN         0x00038000
#define RIAAR_RXROM_MAX         0x00038800

/*
 * Memory Window Base Address Register, 0x7c in PCI config space
 * Once this is set, accesses to the Memory Window Data Access Register
 * (0x84) refer to the word of NIC-local memory whose address is given
 * by this register.  When used in this way, the whole of the address
 * written to this register is significant.
 *
 * This register also provides the 32K-aligned base address for a 32K
 * region of NIC-local memory that the host can directly address in
 * the upper 32K of the 64K of PCI memory space allocated to the chip.
 * In this case, the bottom 15 bits of the register are ignored.
 *
 * Note that the address written to the MWBAR should lie in the range
 * 0x00000000 <= address < 0x00020000.  The rest of the range up to 1M
 * (i.e. 0x00200000 <= address < 0x01000000) would be valid if external
 * memory were present, but it's only supported on the 5700, not the
 * 5701/5703/5704.
 */
#define PCI_CONF_BGE_MWBAR      0x7c
#define PCI_CONF_BGE_MWDAR      0x84
#define MWBAR_GRANULARITY       0x00008000  /* 32k  */
#define MWBAR_GRANULE_MASK      (MWBAR_GRANULARITY-1)
#define MWBAR_ONCHIP_MAX        0x00020000  /* 128k */

/*
 * The PCI express device control register and device status register
 * which are only applicable on BCM5751 and BCM5721.
 */
#define PCI_CONF_DEV_CTRL       0xd8
#define READ_REQ_SIZE_MAX       0x5000
#define DEV_CTRL_NO_SNOOP       0x0800
#define DEV_CTRL_RELAXED        0x0010

#define PCI_CONF_DEV_STUS       0xda
#define DEVICE_ERROR_STUS       0xf

#define NIC_MEM_WINDOW_OFFSET       0x00008000  /* 32k  */

/*
 * Where to find things in NIC-local (on-chip) memory
 */
#define NIC_MEM_SEND_RINGS      0x0100
#define NIC_MEM_SEND_RING(ring)     (0x0100+16*(ring))
#define NIC_MEM_RECV_RINGS      0x0200
#define NIC_MEM_RECV_RING(ring)     (0x0200+16*(ring))
#define NIC_MEM_STATISTICS      0x0300
#define NIC_MEM_STATISTICS_SIZE     0x0800
#define NIC_MEM_STATUS_BLOCK        0x0b00
#define NIC_MEM_STATUS_SIZE     0x0050
#define NIC_MEM_GENCOMM         0x0b50


/*
 * Note: the (non-bogus) values below are appropriate for systems
 * without external memory.  They would be different on a 5700 with
 * external memory.
 *
 * Note: The higher send ring addresses and the mini ring shadow
 * buffer address are dummies - systems without external memory
 * are limited to 4 send rings and no mini receive ring.
 */
#define NIC_MEM_SHADOW_DMA      0x2000
#define NIC_MEM_SHADOW_SEND_1_4     0x4000
#define NIC_MEM_SHADOW_SEND_5_6     0x6000      /* bogus    */
#define NIC_MEM_SHADOW_SEND_7_8     0x7000      /* bogus    */
#define NIC_MEM_SHADOW_SEND_9_16    0x8000      /* bogus    */
#define NIC_MEM_SHADOW_BUFF_STD     0x6000
#define NIC_MEM_SHADOW_BUFF_JUMBO   0x7000
#define NIC_MEM_SHADOW_BUFF_MINI    0x8000      /* bogus    */
#define NIC_MEM_SHADOW_SEND_RING(ring, nslots)  (0x4000 + 4*(ring)*(nslots))

/*
 * Put this in the GENCOMM port to tell the firmware not to run PXE
 */
#define T3_MAGIC_NUMBER         0x4b657654u

/*
 * The remaining registers appear in the low 32K of regular
 * PCI Memory Address Space
 */

/*
 * All the state machine control registers below have at least a
 * <RESET> bit and an <ENABLE> bit as defined below.  Some also
 * have an <ATTN_ENABLE> bit.
 */
#define STATE_MACHINE_ATTN_ENABLE_BIT   0x00000004
#define STATE_MACHINE_ENABLE_BIT    0x00000002
#define STATE_MACHINE_RESET_BIT     0x00000001

#define TRANSMIT_MAC_MODE_REG       0x045c
#define SEND_DATA_INITIATOR_MODE_REG    0x0c00
#define SEND_DATA_COMPLETION_MODE_REG   0x1000
#define SEND_BD_SELECTOR_MODE_REG   0x1400
#define SEND_BD_INITIATOR_MODE_REG  0x1800
#define SEND_BD_COMPLETION_MODE_REG 0x1c00

#define RECEIVE_MAC_MODE_REG        0x0468
#define RCV_LIST_PLACEMENT_MODE_REG 0x2000
#define RCV_DATA_BD_INITIATOR_MODE_REG  0x2400
#define RCV_DATA_COMPLETION_MODE_REG    0x2800
#define RCV_BD_INITIATOR_MODE_REG   0x2c00
#define RCV_BD_COMPLETION_MODE_REG  0x3000
#define RCV_LIST_SELECTOR_MODE_REG  0x3400

#define MBUF_CLUSTER_FREE_MODE_REG  0x3800
#define HOST_COALESCE_MODE_REG      0x3c00
#define MEMORY_ARBITER_MODE_REG     0x4000
#define BUFFER_MANAGER_MODE_REG     0x4400
#define READ_DMA_MODE_REG       0x4800
#define WRITE_DMA_MODE_REG      0x4c00
#define DMA_COMPLETION_MODE_REG     0x6400

/*
 * Other bits in some of the above state machine control registers
 */

/*
 * Transmit MAC Mode Register
 * (TRANSMIT_MAC_MODE_REG, 0x045c)
 */
#define TRANSMIT_MODE_LONG_PAUSE    0x00000040
#define TRANSMIT_MODE_BIG_BACKOFF   0x00000020
#define TRANSMIT_MODE_FLOW_CONTROL  0x00000010

/*
 * Receive MAC Mode Register
 * (RECEIVE_MAC_MODE_REG, 0x0468)
 */
#define RECEIVE_MODE_KEEP_VLAN_TAG  0x00000400
#define RECEIVE_MODE_NO_CRC_CHECK   0x00000200
#define RECEIVE_MODE_PROMISCUOUS    0x00000100
#define RECEIVE_MODE_LENGTH_CHECK   0x00000080
#define RECEIVE_MODE_ACCEPT_RUNTS   0x00000040
#define RECEIVE_MODE_ACCEPT_OVERSIZE    0x00000020
#define RECEIVE_MODE_KEEP_PAUSE     0x00000010
#define RECEIVE_MODE_FLOW_CONTROL   0x00000004

/*
 * Receive BD Initiator Mode Register
 * (RCV_BD_INITIATOR_MODE_REG, 0x2c00)
 *
 * Each of these bits controls whether ATTN is asserted
 * on a particular condition
 */
#define RCV_BD_DISABLED_RING_ATTN   0x00000004

/*
 * Receive Data & Receive BD Initiator Mode Register
 * (RCV_DATA_BD_INITIATOR_MODE_REG, 0x2400)
 *
 * Each of these bits controls whether ATTN is asserted
 * on a particular condition
 */
#define RCV_DATA_BD_ILL_RING_ATTN   0x00000010
#define RCV_DATA_BD_FRAME_SIZE_ATTN 0x00000008
#define RCV_DATA_BD_NEED_JUMBO_ATTN 0x00000004

#define RCV_DATA_BD_ALL_ATTN_BITS   0x0000001c

/*
 * Host Coalescing Mode Control Register
 * (HOST_COALESCE_MODE_REG, 0x3c00)
 */
#define COALESCE_64_BYTE_RINGS      12
#define COALESCE_NO_INT_ON_COAL_FORCE   0x00001000
#define COALESCE_NO_INT_ON_DMAD_FORCE   0x00000800
#define COALESCE_CLR_TICKS_TX       0x00000400
#define COALESCE_CLR_TICKS_RX       0x00000200
#define COALESCE_32_BYTE_STATUS     0x00000100
#define COALESCE_64_BYTE_STATUS     0x00000080
#define COALESCE_NOW            0x00000008

/*
 * Memory Arbiter Mode Register
 * (MEMORY_ARBITER_MODE_REG, 0x4000)
 */
#define MEMORY_ARBITER_ENABLE       0x00000002

/*
 * Buffer Manager Mode Register
 * (BUFFER_MANAGER_MODE_REG, 0x4400)
 *
 * In addition to the usual error-attn common to most state machines
 * this register has a separate bit for attn on running-low-on-mbufs
 */
#define BUFF_MGR_TEST_MODE      0x00000008
#define BUFF_MGR_MBUF_LOW_ATTN_ENABLE   0x00000010

#define BUFF_MGR_ALL_ATTN_BITS      0x00000014

/*
 * Read and Write DMA Mode Registers (READ_DMA_MODE_REG,
 * 0x4800 and WRITE_DMA_MODE_REG, 0x4c00)
 *
 * These registers each contain a 2-bit priority field, which controls
 * the relative priority of that type of DMA (read vs. write vs. MSI),
 * and a set of bits that control whether ATTN is asserted on each
 * particular condition
 */
#define DMA_PRIORITY_MASK       0xc0000000
#define DMA_PRIORITY_SHIFT      30
#define ALL_DMA_ATTN_BITS       0x000003fc

/*
 * BCM5755, 5755M, 5906, 5906M only
 * 1 - Enable Fix. Device will send out the status block before
 *     the interrupt message
 * 0 - Disable fix. Device will send out the interrupt message
 *     before the status block
 */
#define DMA_STATUS_TAG_FIX_CQ12384  0x20000000

/*
 * End of state machine control register definitions
 */


/*
 * High priority mailbox registers.
 * Mailbox Registers (8 bytes each, but high half unused)
 */
#define INTERRUPT_MBOX_0_REG        0x0200
#define INTERRUPT_MBOX_1_REG        0x0208
#define INTERRUPT_MBOX_2_REG        0x0210
#define INTERRUPT_MBOX_3_REG        0x0218
#define INTERRUPT_MBOX_REG(n)       (0x0200+8*(n))

/*
 * Low priority mailbox registers, for BCM5906, BCM5906M.
 */
#define INTERRUPT_LP_MBOX_0_REG     0x5800

/*
 * Ring Producer/Consumer Index (Mailbox) Registers
 */
#define RECV_STD_PROD_INDEX_REG     0x0268
#define RECV_JUMBO_PROD_INDEX_REG   0x0270
#define RECV_MINI_PROD_INDEX_REG    0x0278
#define RECV_RING_CONS_INDEX_REGS   0x0280
#define SEND_RING_HOST_PROD_INDEX_REGS  0x0300
#define SEND_RING_NIC_PROD_INDEX_REGS   0x0380

#define RECV_RING_CONS_INDEX_REG(ring)  (0x0280+8*(ring))
#define SEND_RING_HOST_INDEX_REG(ring)  (0x0300+8*(ring))
#define SEND_RING_NIC_INDEX_REG(ring)   (0x0380+8*(ring))

/*
 * Ethernet MAC Mode Register
 */
#define ETHERNET_MAC_MODE_REG       0x0400
#define ETHERNET_MODE_ENABLE_FHDE   0x00800000
#define ETHERNET_MODE_ENABLE_RDE    0x00400000
#define ETHERNET_MODE_ENABLE_TDE    0x00200000
#define ETHERNET_MODE_ENABLE_MIP    0x00100000
#define ETHERNET_MODE_ENABLE_ACPI   0x00080000
#define ETHERNET_MODE_ENABLE_MAGIC_PKT  0x00040000
#define ETHERNET_MODE_SEND_CFGS     0x00020000
#define ETHERNET_MODE_FLUSH_TX_STATS    0x00010000
#define ETHERNET_MODE_CLEAR_TX_STATS    0x00008000
#define ETHERNET_MODE_ENABLE_TX_STATS   0x00004000
#define ETHERNET_MODE_FLUSH_RX_STATS    0x00002000
#define ETHERNET_MODE_CLEAR_RX_STATS    0x00001000
#define ETHERNET_MODE_ENABLE_RX_STATS   0x00000800
#define ETHERNET_MODE_LINK_POLARITY 0x00000400
#define ETHERNET_MODE_MAX_DEFER     0x00000200
#define ETHERNET_MODE_ENABLE_TX_BURST   0x00000100
#define ETHERNET_MODE_TAGGED_MODE   0x00000080
#define ETHERNET_MODE_MAC_LOOPBACK  0x00000010
#define ETHERNET_MODE_PORTMODE_MASK 0x0000000c
#define ETHERNET_MODE_PORTMODE_TBI  0x0000000c
#define ETHERNET_MODE_PORTMODE_GMII 0x00000008
#define ETHERNET_MODE_PORTMODE_MII  0x00000004
#define ETHERNET_MODE_PORTMODE_NONE 0x00000000
#define ETHERNET_MODE_HALF_DUPLEX   0x00000002
#define ETHERNET_MODE_GLOBAL_RESET  0x00000001

/*
 * Ethernet MAC Status & Event Registers
 */
#define ETHERNET_MAC_STATUS_REG     0x0404
#define ETHERNET_STATUS_MI_INT      0x00800000
#define ETHERNET_STATUS_MI_COMPLETE 0x00400000
#define ETHERNET_STATUS_LINK_CHANGED    0x00001000
#define ETHERNET_STATUS_PCS_ERROR   0x00000400
#define ETHERNET_STATUS_SYNC_CHANGED    0x00000010
#define ETHERNET_STATUS_CFG_CHANGED 0x00000008
#define ETHERNET_STATUS_RECEIVING_CFG   0x00000004
#define ETHERNET_STATUS_SIGNAL_DETECT   0x00000002
#define ETHERNET_STATUS_PCS_SYNCHED 0x00000001

#define ETHERNET_MAC_EVENT_ENABLE_REG   0x0408
#define ETHERNET_EVENT_MI_INT       0x00800000
#define ETHERNET_EVENT_LINK_INT     0x00001000
#define ETHERNET_STATUS_PCS_ERROR_INT   0x00000400

/*
 * Ethernet MAC LED Control Register
 *
 * NOTE: PHY mode 1 *MUST* be selected; this is the hardware default and
 * the external LED driver circuitry is wired up to assume that this mode
 * will always be selected.  Software must not change it!
 */
#define ETHERNET_MAC_LED_CONTROL_REG    0x040c
#define LED_CONTROL_OVERRIDE_BLINK  0x80000000
#define LED_CONTROL_BLINK_PERIOD_MASK   0x7ff80000
#define LED_CONTROL_LED_MODE_MASK   0x00001800
#define LED_CONTROL_LED_MODE_5700   0x00000000
#define LED_CONTROL_LED_MODE_PHY_1  0x00000800  /* mandatory    */
#define LED_CONTROL_LED_MODE_PHY_2  0x00001000
#define LED_CONTROL_LED_MODE_RESERVED   0x00001800
#define LED_CONTROL_TRAFFIC_LED_STATUS  0x00000400
#define LED_CONTROL_10MBPS_LED_STATUS   0x00000200
#define LED_CONTROL_100MBPS_LED_STATUS  0x00000100
#define LED_CONTROL_1000MBPS_LED_STATUS 0x00000080
#define LED_CONTROL_BLINK_TRAFFIC   0x00000040
#define LED_CONTROL_TRAFFIC_LED     0x00000020
#define LED_CONTROL_OVERRIDE_TRAFFIC    0x00000010
#define LED_CONTROL_10MBPS_LED      0x00000008
#define LED_CONTROL_100MBPS_LED     0x00000004
#define LED_CONTROL_1000MBPS_LED    0x00000002
#define LED_CONTROL_OVERRIDE_LINK   0x00000001
#define LED_CONTROL_DEFAULT     0x02000800

/*
 * MAC Address registers
 *
 * These four eight-byte registers each hold one unicast address
 * (six bytes), right justified & zero-filled on the left.
 * They will normally all be set to the same value, as a station
 * usually only has one h/w address.  The value in register 0 is
 * used for pause packets; any of the four can be specified for
 * substitution into other transmitted packets if required.
 */
#define MAC_ADDRESS_0_REG       0x0410
#define MAC_ADDRESS_1_REG       0x0418
#define MAC_ADDRESS_2_REG       0x0420
#define MAC_ADDRESS_3_REG       0x0428

#define MAC_ADDRESS_REG(n)      (0x0410+8*(n))
#define MAC_ADDRESS_REGS_MAX        4

/*
 * More MAC Registers ...
 */
#define MAC_TX_RANDOM_BACKOFF_REG   0x0438
#define MAC_RX_MTU_SIZE_REG     0x043c
#define MAC_RX_MTU_DEFAULT      0x000005f2  /* 1522 */
#define MAC_TX_LENGTHS_REG      0x0464
#define MAC_TX_LENGTHS_DEFAULT      0x00002620

/*
 * MII access registers
 */
#define MI_COMMS_REG            0x044c
#define MI_COMMS_START          0x20000000
#define MI_COMMS_READ_FAILED        0x10000000
#define MI_COMMS_COMMAND_MASK       0x0c000000
#define MI_COMMS_COMMAND_READ       0x08000000
#define MI_COMMS_COMMAND_WRITE      0x04000000
#define MI_COMMS_ADDRESS_MASK       0x03e00000
#define MI_COMMS_ADDRESS_SHIFT      21
#define MI_COMMS_REGISTER_MASK      0x001f0000
#define MI_COMMS_REGISTER_SHIFT     16
#define MI_COMMS_DATA_MASK      0x0000ffff
#define MI_COMMS_DATA_SHIFT     0

#define MI_STATUS_REG           0x0450
#define MI_STATUS_10MBPS        0x00000002
#define MI_STATUS_LINK          0x00000001

#define MI_MODE_REG         0x0454
#define MI_MODE_CLOCK_MASK      0x001f0000
#define MI_MODE_AUTOPOLL        0x00000010
#define MI_MODE_POLL_SHORT_PREAMBLE 0x00000002
#define MI_MODE_DEFAULT         0x000c0000

#define MI_AUTOPOLL_STATUS_REG      0x0458
#define MI_AUTOPOLL_ERROR       0x00000001

#define TRANSMIT_MAC_STATUS_REG     0x0460
#define TRANSMIT_STATUS_ODI_OVERRUN 0x00000020
#define TRANSMIT_STATUS_ODI_UNDERRUN    0x00000010
#define TRANSMIT_STATUS_LINK_UP     0x00000008
#define TRANSMIT_STATUS_SENT_XON    0x00000004
#define TRANSMIT_STATUS_SENT_XOFF   0x00000002
#define TRANSMIT_STATUS_RCVD_XOFF   0x00000001

#define RECEIVE_MAC_STATUS_REG      0x046c
#define RECEIVE_STATUS_RCVD_XON     0x00000004
#define RECEIVE_STATUS_RCVD_XOFF    0x00000002
#define RECEIVE_STATUS_SENT_XOFF    0x00000001

/*
 * These four-byte registers constitute a hash table for deciding
 * whether to accept incoming multicast packets.  The bits are
 * numbered in big-endian fashion, from hash 0 => the MSB of
 * register 0 to hash 127 => the LSB of the highest-numbered
 * register.
 *
 * NOTE: the 5704 can use a 256-bit table (registers 0-7) if
 * enabled by setting the appropriate bit in the Rx MAC mode
 * register.  Otherwise, and on all earlier chips, the table
 * is only 128 bits (registers 0-3).
 */
#define MAC_HASH_0_REG          0x0470
#define MAC_HASH_1_REG          0x0474
#define MAC_HASH_2_REG          0x0478
#define MAC_HASH_3_REG          0x047c
#define MAC_HASH_4_REG          0x????
#define MAC_HASH_5_REG          0x????
#define MAC_HASH_6_REG          0x????
#define MAC_HASH_7_REG          0x????
#define MAC_HASH_REG(n)         (0x470+4*(n))

/*
 * Receive Rules Registers: 16 pairs of control+mask/value pairs
 */
#define RCV_RULES_CONTROL_0_REG     0x0480
#define RCV_RULES_MASK_0_REG        0x0484
#define RCV_RULES_CONTROL_15_REG    0x04f8
#define RCV_RULES_MASK_15_REG       0x04fc
#define RCV_RULES_CONFIG_REG        0x0500
#define RCV_RULES_CONFIG_DEFAULT    0x00000008

#define RECV_RULES_NUM_MAX      16
#define RECV_RULE_CONTROL_REG(rule) (RCV_RULES_CONTROL_0_REG+8*(rule))
#define RECV_RULE_MASK_REG(rule)    (RCV_RULES_MASK_0_REG+8*(rule))

#define RECV_RULE_CTL_ENABLE        0x80000000
#define RECV_RULE_CTL_AND       0x40000000
#define RECV_RULE_CTL_P1        0x20000000
#define RECV_RULE_CTL_P2        0x10000000
#define RECV_RULE_CTL_P3        0x08000000
#define RECV_RULE_CTL_MASK      0x04000000
#define RECV_RULE_CTL_DISCARD       0x02000000
#define RECV_RULE_CTL_MAP       0x01000000
#define RECV_RULE_CTL_RESV_BITS     0x00fc0000
#define RECV_RULE_CTL_OP        0x00030000
#define RECV_RULE_CTL_OP_EQ     0x00000000
#define RECV_RULE_CTL_OP_NEQ        0x00010000
#define RECV_RULE_CTL_OP_GREAT      0x00020000
#define RECV_RULE_CTL_OP_LESS       0x00030000
#define RECV_RULE_CTL_HEADER        0x0000e000
#define RECV_RULE_CTL_HEADER_FRAME  0x00000000
#define RECV_RULE_CTL_HEADER_IP     0x00002000
#define RECV_RULE_CTL_HEADER_TCP    0x00004000
#define RECV_RULE_CTL_HEADER_UDP    0x00006000
#define RECV_RULE_CTL_HEADER_DATA   0x00008000
#define RECV_RULE_CTL_CLASS_BITS    0x00001f00
#define RECV_RULE_CTL_CLASS(ring)   (((ring) << 8) & \
                        RECV_RULE_CTL_CLASS_BITS)
#define RECV_RULE_CTL_OFFSET        0x000000ff

/*
 * Receive Rules definition
 */
#define ETHERHEADER_DEST_OFFSET     0x00
#define IPHEADER_PROTO_OFFSET       0x08
#define IPHEADER_SIP_OFFSET     0x0c
#define IPHEADER_DIP_OFFSET     0x10
#define TCPHEADER_SPORT_OFFSET      0x00
#define TCPHEADER_DPORT_OFFSET      0x02
#define UDPHEADER_SPORT_OFFSET      0x00
#define UDPHEADER_DPORT_OFFSET      0x02

#define RULE_MATCH(ring)    (RECV_RULE_CTL_ENABLE | RECV_RULE_CTL_OP_EQ | \
                    RECV_RULE_CTL_CLASS((ring)))

#define RULE_MATCH_MASK(ring)   (RULE_MATCH(ring) | RECV_RULE_CTL_MASK)

#define RULE_DEST_MAC_1(ring)   (RULE_MATCH(ring) | \
                    RECV_RULE_CTL_HEADER_FRAME | \
                    ETHERHEADER_DEST_OFFSET)

#define RULE_DEST_MAC_2(ring)   (RULE_MATCH_MASK(ring) | \
                    RECV_RULE_CTL_HEADER_FRAME | \
                    ETHERHEADER_DEST_OFFSET + 4)

#define RULE_LOCAL_IP(ring) (RULE_MATCH(ring) | RECV_RULE_CTL_HEADER_IP | \
                    IPHEADER_DIP_OFFSET)

#define RULE_REMOTE_IP(ring)    (RULE_MATCH(ring) | RECV_RULE_CTL_HEADER_IP | \
                    IPHEADER_SIP_OFFSET)

#define RULE_IP_PROTO(ring) (RULE_MATCH_MASK(ring) | \
                    RECV_RULE_CTL_HEADER_IP | \
                    IPHEADER_PROTO_OFFSET)

#define RULE_TCP_SPORT(ring)    (RULE_MATCH_MASK(ring) | \
                    RECV_RULE_CTL_HEADER_TCP | \
                    TCPHEADER_SPORT_OFFSET)

#define RULE_TCP_DPORT(ring)    (RULE_MATCH_MASK(ring) | \
                    RECV_RULE_CTL_HEADER_TCP | \
                    TCPHEADER_DPORT_OFFSET)

#define RULE_UDP_SPORT(ring)    (RULE_MATCH_MASK(ring) | \
                    RECV_RULE_CTL_HEADER_UDP | \
                    UDPHEADER_SPORT_OFFSET)

#define RULE_UDP_DPORT(ring)    (RULE_MATCH_MASK(ring) | \
                    RECV_RULE_CTL_HEADER_UDP | \
                    UDPHEADER_DPORT_OFFSET)

/*
 * 1000BaseX low-level access registers
 */
#define MAC_GIGABIT_PCS_TEST_REG    0x0440
#define MAC_GIGABIT_PCS_TEST_ENABLE 0x00100000
#define MAC_GIGABIT_PCS_TEST_PATTERN    0x000fffff
#define TX_1000BASEX_AUTONEG_REG    0x0444
#define RX_1000BASEX_AUTONEG_REG    0x0448

/*
 * Autoneg code bits for the 1000BASE-X AUTONEG registers
 */
#define AUTONEG_CODE_PAUSE      0x00008000
#define AUTONEG_CODE_HALF_DUPLEX    0x00004000
#define AUTONEG_CODE_FULL_DUPLEX    0x00002000
#define AUTONEG_CODE_NEXT_PAGE      0x00000080
#define AUTONEG_CODE_ACKNOWLEDGE    0x00000040
#define AUTONEG_CODE_FAULT_MASK     0x00000030
#define AUTONEG_CODE_FAULT_ANEG_ERR 0x00000030
#define AUTONEG_CODE_FAULT_LINK_FAIL    0x00000020
#define AUTONEG_CODE_FAULT_OFFLINE  0x00000010
#define AUTONEG_CODE_ASYM_PAUSE     0x00000001

/*
 * SerDes Registers (5703S/5704S only)
 */
#define SERDES_CONTROL_REG      0x0590
#define SERDES_CONTROL_TBI_LOOPBACK 0x00020000
#define SERDES_CONTROL_COMMA_DETECT 0x00010000
#define SERDES_CONTROL_TX_DISABLE   0x00004000
#define SERDES_STATUS_REG       0x0594
#define SERDES_STATUS_COMMA_DETECTED    0x00000100
#define SERDES_STATUS_RXSTAT        0x000000ff

/*
 * Statistic Registers (5705/5788/5721/5751/5752/5714/5715 only)
 */
#define STAT_IFHCOUT_OCTETS_REG     0x0800
#define STAT_ETHER_COLLIS_REG       0x0808
#define STAT_OUTXON_SENT_REG        0x080c
#define STAT_OUTXOFF_SENT_REG       0x0810
#define STAT_DOT3_INTMACTX_ERR_REG      0x0818
#define STAT_DOT3_SCOLLI_FRAME_REG      0x081c
#define STAT_DOT3_MCOLLI_FRAME_REG      0x0820
#define STAT_DOT3_DEFERED_TX_REG        0x0824
#define STAT_DOT3_EXCE_COLLI_REG        0x082c
#define STAT_DOT3_LATE_COLLI_REG        0x0830
#define STAT_IFHCOUT_UPKGS_REG      0x086c
#define STAT_IFHCOUT_MPKGS_REG      0x0870
#define STAT_IFHCOUT_BPKGS_REG      0x0874

#define STAT_IFHCIN_OCTETS_REG      0x0880
#define STAT_ETHER_FRAGMENT_REG     0x0888
#define STAT_IFHCIN_UPKGS_REG       0x088c
#define STAT_IFHCIN_MPKGS_REG       0x0890
#define STAT_IFHCIN_BPKGS_REG       0x0894

#define STAT_DOT3_FCS_ERR_REG       0x0898
#define STAT_DOT3_ALIGN_ERR_REG     0x089c
#define STAT_XON_PAUSE_RX_REG       0x08a0
#define STAT_XOFF_PAUSE_RX_REG      0x08a4
#define STAT_MAC_CTRL_RX_REG        0x08a8
#define STAT_XOFF_STATE_ENTER_REG       0x08ac
#define STAT_DOT3_FRAME_TOOLONG_REG     0x08b0
#define STAT_ETHER_JABBERS_REG      0x08b4
#define STAT_ETHER_UNDERSIZE_REG        0x08b8
#define SIZE_OF_STATISTIC_REG       0x1B
/*
 * Send Data Initiator Registers
 */
#define SEND_INIT_STATS_CONTROL_REG 0x0c08
#define SEND_INIT_STATS_ZERO        0x00000010
#define SEND_INIT_STATS_FLUSH       0x00000008
#define SEND_INIT_STATS_CLEAR       0x00000004
#define SEND_INIT_STATS_FASTER      0x00000002
#define SEND_INIT_STATS_ENABLE      0x00000001

#define SEND_INIT_STATS_ENABLE_MASK_REG 0x0c0c

/*
 * Send Buffer Descriptor Selector Control Registers
 */
#define SEND_BD_SELECTOR_STATUS_REG 0x1404
#define SEND_BD_SELECTOR_HWDIAG_REG 0x1408
#define SEND_BD_SELECTOR_INDEX_REG(n)   (0x1440+4*(n))

/*
 * Receive List Placement Registers
 */
#define RCV_LP_CONFIG_REG       0x2010
#define RCV_LP_CONFIG_DEFAULT       0x00000009
#define RCV_LP_CONFIG(rings)        (((rings) << 3) | 0x1)

#define RCV_LP_STATS_CONTROL_REG    0x2014
#define RCV_LP_STATS_ZERO       0x00000010
#define RCV_LP_STATS_FLUSH      0x00000008
#define RCV_LP_STATS_CLEAR      0x00000004
#define RCV_LP_STATS_FASTER     0x00000002
#define RCV_LP_STATS_ENABLE     0x00000001

#define RCV_LP_STATS_ENABLE_MASK_REG    0x2018
#define RCV_LP_STATS_DISABLE_MACTQ  0x040000

/*
 * Receive Data & BD Initiator Registers
 */
#define RCV_INITIATOR_STATUS_REG    0x2404

/*
 * Receive Buffer Descriptor Ring Control Block Registers
 * NB: sixteen bytes (128 bits) each
 */
#define JUMBO_RCV_BD_RING_RCB_REG   0x2440
#define STD_RCV_BD_RING_RCB_REG     0x2450
#define MINI_RCV_BD_RING_RCB_REG    0x2460

/*
 * Receive Buffer Descriptor Ring Replenish Threshold Registers
 */
#define MINI_RCV_BD_REPLENISH_REG   0x2c14
#define MINI_RCV_BD_REPLENISH_DEFAULT   0x00000080  /* 128  */
#define STD_RCV_BD_REPLENISH_REG    0x2c18
#define STD_RCV_BD_REPLENISH_DEFAULT    0x00000002  /* 2    */
#define JUMBO_RCV_BD_REPLENISH_REG  0x2c1c
#define JUMBO_RCV_BD_REPLENISH_DEFAULT  0x00000020  /* 32   */

/*
 * Host Coalescing Engine Control Registers
 */
#define RCV_COALESCE_TICKS_REG      0x3c08
#define RCV_COALESCE_TICKS_DEFAULT  0x00000096  /* 150  */
#define SEND_COALESCE_TICKS_REG     0x3c0c
#define SEND_COALESCE_TICKS_DEFAULT 0x00000096  /* 150  */
#define RCV_COALESCE_MAX_BD_REG     0x3c10
#define RCV_COALESCE_MAX_BD_DEFAULT 0x0000000a  /* 10   */
#define SEND_COALESCE_MAX_BD_REG    0x3c14
#define SEND_COALESCE_MAX_BD_DEFAULT    0x0000000a  /* 10   */
#define RCV_COALESCE_INT_TICKS_REG  0x3c18
#define RCV_COALESCE_INT_TICKS_DEFAULT  0x00000000  /* 0    */
#define SEND_COALESCE_INT_TICKS_REG 0x3c1c
#define SEND_COALESCE_INT_TICKS_DEFAULT 0x00000000  /* 0    */
#define RCV_COALESCE_INT_BD_REG     0x3c20
#define RCV_COALESCE_INT_BD_DEFAULT 0x00000000  /* 0    */
#define SEND_COALESCE_INT_BD_REG    0x3c24
#define SEND_COALESCE_INT_BD_DEFAULT    0x00000000  /* 0    */
#define STATISTICS_TICKS_REG        0x3c28
#define STATISTICS_TICKS_DEFAULT    0x000f4240  /* 1000000 */
#define STATISTICS_HOST_ADDR_REG    0x3c30
#define STATUS_BLOCK_HOST_ADDR_REG  0x3c38
#define STATISTICS_BASE_ADDR_REG    0x3c40
#define STATUS_BLOCK_BASE_ADDR_REG  0x3c44
#define FLOW_ATTN_REG           0x3c48

#define NIC_JUMBO_RECV_INDEX_REG    0x3c50
#define NIC_STD_RECV_INDEX_REG      0x3c54
#define NIC_MINI_RECV_INDEX_REG     0x3c58
#define NIC_DIAG_RETURN_INDEX_REG(n)    (0x3c80+4*(n))
#define NIC_DIAG_SEND_INDEX_REG(n)  (0x3cc0+4*(n))

/*
 * Mbuf Pool Initialisation & Watermark Registers
 *
 * There are some conflicts in the PRM; compare the recommendations
 * on pp. 115, 236, and 339.  The values here were recommended by
 * dkim@broadcom.com (and the PRM should be corrected soon ;-)
 */
#define BUFFER_MANAGER_STATUS_REG   0x4404
#define MBUF_POOL_BASE_REG      0x4408
#define MBUF_POOL_BASE_DEFAULT      0x00008000
#define MBUF_POOL_BASE_5721     0x00010000
#define MBUF_POOL_BASE_5704     0x00010000
#define MBUF_POOL_BASE_5705     0x00010000
#define MBUF_POOL_LENGTH_REG        0x440c
#define MBUF_POOL_LENGTH_DEFAULT    0x00018000
#define MBUF_POOL_LENGTH_5704       0x00010000
#define MBUF_POOL_LENGTH_5705       0x00008000
#define MBUF_POOL_LENGTH_5721       0x00008000
#define RDMA_MBUF_LOWAT_REG     0x4410
#define RDMA_MBUF_LOWAT_DEFAULT     0x00000050
#define RDMA_MBUF_LOWAT_5705        0x00000000
#define RDMA_MBUF_LOWAT_5906        0x00000000
#define RDMA_MBUF_LOWAT_JUMBO       0x00000130
#define RDMA_MBUF_LOWAT_5714_JUMBO  0x00000000
#define MAC_RX_MBUF_LOWAT_REG       0x4414
#define MAC_RX_MBUF_LOWAT_DEFAULT   0x00000020
#define MAC_RX_MBUF_LOWAT_5705      0x00000010
#define MAC_RX_MBUF_LOWAT_5906      0x00000004
#define MAC_RX_MBUF_LOWAT_JUMBO     0x00000098
#define MAC_RX_MBUF_LOWAT_5714_JUMBO    0x0000004b
#define MBUF_HIWAT_REG          0x4418
#define MBUF_HIWAT_DEFAULT      0x00000060
#define MBUF_HIWAT_5705         0x00000060
#define MBUF_HIWAT_5906         0x00000010
#define MBUF_HIWAT_JUMBO        0x0000017c
#define MBUF_HIWAT_5714_JUMBO       0x00000096

/*
 * DMA Descriptor Pool Initialisation & Watermark Registers
 */
#define DMAD_POOL_BASE_REG      0x442c
#define DMAD_POOL_BASE_DEFAULT      0x00002000
#define DMAD_POOL_LENGTH_REG        0x4430
#define DMAD_POOL_LENGTH_DEFAULT    0x00002000
#define DMAD_POOL_LOWAT_REG     0x4434
#define DMAD_POOL_LOWAT_DEFAULT     0x00000005  /* 5    */
#define DMAD_POOL_HIWAT_REG     0x4438
#define DMAD_POOL_HIWAT_DEFAULT     0x0000000a  /* 10   */

/*
 * More threshold/watermark registers ...
 */
#define RECV_FLOW_THRESHOLD_REG     0x4458
#define LOWAT_MAX_RECV_FRAMES_REG   0x0504
#define LOWAT_MAX_RECV_FRAMES_DEFAULT   0x00000002

/*
 * Read/Write DMA Status Registers
 */
#define READ_DMA_STATUS_REG     0x4804
#define WRITE_DMA_STATUS_REG        0x4c04

/*
 * RX/TX RISC Registers
 */
#define RX_RISC_MODE_REG        0x5000
#define RX_RISC_STATE_REG       0x5004
#define RX_RISC_PC_REG          0x501c
#define TX_RISC_MODE_REG        0x5400
#define TX_RISC_STATE_REG       0x5404
#define TX_RISC_PC_REG          0x541c

/*
 * V? RISC Registerss
 */
#define VCPU_STATUS_REG         0x5100
#define VCPU_INIT_DONE          0x04000000
#define VCPU_DRV_RESET          0x08000000

#define VCPU_EXT_CTL            0x6890
#define VCPU_EXT_CTL_HALF       0x00400000

#define FTQ_RESET_REG           0x5c00

#define MSI_MODE_REG            0x6000
#define MSI_PRI_HIGHEST         0xc0000000
#define MSI_MSI_ENABLE          0x00000002
#define MSI_ERROR_ATTENTION     0x0000001c

#define MSI_STATUS_REG          0x6004

#define MODE_CONTROL_REG        0x6800
#define MODE_ROUTE_MCAST_TO_RX_RISC 0x40000000
#define MODE_4X_NIC_SEND_RINGS      0x20000000
#define MODE_INT_ON_FLOW_ATTN       0x10000000
#define MODE_INT_ON_DMA_ATTN        0x08000000
#define MODE_INT_ON_MAC_ATTN        0x04000000
#define MODE_INT_ON_RXRISC_ATTN     0x02000000
#define MODE_INT_ON_TXRISC_ATTN     0x01000000
#define MODE_RECV_NO_PSEUDO_HDR_CSUM    0x00800000
#define MODE_SEND_NO_PSEUDO_HDR_CSUM    0x00100000
#define MODE_HOST_SEND_BDS      0x00020000
#define MODE_HOST_STACK_UP      0x00010000
#define MODE_FORCE_32_BIT_PCI       0x00008000
#define MODE_NO_INT_ON_RECV     0x00004000
#define MODE_NO_INT_ON_SEND     0x00002000
#define MODE_ALLOW_BAD_FRAMES       0x00000800
#define MODE_NO_CRC         0x00000400
#define MODE_NO_FRAME_CRACKING      0x00000200
#define MODE_WORD_SWAP_FRAME        0x00000020
#define MODE_BYTE_SWAP_FRAME        0x00000010
#define MODE_WORD_SWAP_NONFRAME     0x00000004
#define MODE_BYTE_SWAP_NONFRAME     0x00000002
#define MODE_UPDATE_ON_COAL_ONLY    0x00000001

/*
 * Miscellaneous Configuration Register
 *
 * This contains various bits relating to power control (which differ
 * among different members of the chip family), but the important bits
 * for our purposes are the RESET bit and the Timer Prescaler field.
 *
 * The RESET bit in this register serves to reset the whole chip, even
 * including the PCI interface(!)  Once it's set, the chip will not
 * respond to ANY accesses -- not even CONFIG space -- until the reset
 * completes internally.  According to the PRM, this should take less
 * than 100us.  Any access during this period will get a bus error.
 *
 * The Timer Prescaler field must be programmed so that the timer period
 * is as near as possible to 1us.  The value in this field should be
 * the Core Clock frequency in MHz minus 1.  From my reading of the PRM,
 * the Core Clock should always be 66MHz (independently of the bus speed,
 * at least for PCI rather than PCI-X), so this register must be set to
 * the value 0x82 ((66-1) << 1).
 */
#define CORE_CLOCK_MHZ          66
#define MISC_CONFIG_REG         0x6804
#define MISC_CONFIG_GRC_RESET_DISABLE   0x20000000
#define MISC_CONFIG_GPHY_POWERDOWN_OVERRIDE 0x04000000
#define MISC_CONFIG_POWERDOWN       0x00100000
#define MISC_CONFIG_POWER_STATE     0x00060000
#define MISC_CONFIG_PRESCALE_MASK   0x000000fe
#define MISC_CONFIG_RESET_BIT       0x00000001
#define MISC_CONFIG_DEFAULT     (((CORE_CLOCK_MHZ)-1) << 1)
#define MISC_CONFIG_EPHY_IDDQ       0x00200000

/*
 * Miscellaneous Local Control Register (MLCR)
 */
#define MISC_LOCAL_CONTROL_REG      0x6808
#define MLCR_PCI_CTRL_SELECT        0x10000000
#define MLCR_LEGACY_PCI_MODE        0x08000000
#define MLCR_AUTO_SEEPROM_ACCESS    0x01000000
#define MLCR_SSRAM_CYCLE_DESELECT   0x00800000
#define MLCR_SSRAM_TYPE         0x00400000
#define MLCR_BANK_SELECT        0x00200000
#define MLCR_SRAM_SIZE_MASK     0x001c0000
#define MLCR_ENABLE_EXTERNAL_MEMORY 0x00020000

#define MLCR_MISC_PINS_OUTPUT_2     0x00010000
#define MLCR_MISC_PINS_OUTPUT_1     0x00008000
#define MLCR_MISC_PINS_OUTPUT_0     0x00004000
#define MLCR_MISC_PINS_OUTPUT_ENABLE_2  0x00002000
#define MLCR_MISC_PINS_OUTPUT_ENABLE_1  0x00001000
#define MLCR_MISC_PINS_OUTPUT_ENABLE_0  0x00000800
#define MLCR_MISC_PINS_INPUT_2      0x00000400  /* R/O  */
#define MLCR_MISC_PINS_INPUT_1      0x00000200  /* R/O  */
#define MLCR_MISC_PINS_INPUT_0      0x00000100  /* R/O  */

#define MLCR_INT_ON_ATTN        0x00000008  /* R/W  */
#define MLCR_SET_INT            0x00000004  /* W/O  */
#define MLCR_CLR_INT            0x00000002  /* W/O  */
#define MLCR_INTA_STATE         0x00000001  /* R/O  */

/*
 * This value defines all GPIO bits as INPUTS, but sets their default
 * values as outputs to HIGH, on the assumption that external circuits
 * (if any) will probably be active-LOW with passive pullups.
 *
 * The Claymore blade uses GPIO1 to control writing to the SEEPROM in
 * just this fashion.  It has to be set as an OUTPUT and driven LOW to
 * enable writing.  Otherwise, the SEEPROM is protected.
 */
#define MLCR_DEFAULT            0x0101c000
#define MLCR_DEFAULT_5714       0x1901c000

/*
 * Serial EEPROM Data/Address Registers (auto-access mode)
 */
#define SERIAL_EEPROM_DATA_REG      0x683c
#define SERIAL_EEPROM_ADDRESS_REG   0x6838
#define SEEPROM_ACCESS_READ     0x80000000
#define SEEPROM_ACCESS_WRITE        0x00000000
#define SEEPROM_ACCESS_COMPLETE     0x40000000
#define SEEPROM_ACCESS_RESET        0x20000000
#define SEEPROM_ACCESS_DEVID_MASK   0x1c000000
#define SEEPROM_ACCESS_START        0x02000000
#define SEEPROM_ACCESS_HALFCLOCK_MASK   0x01ff0000
#define SEEPROM_ACCESS_ADDRESS_MASK 0x0000fffc

#define SEEPROM_ACCESS_DEVID_SHIFT  26      /* bits */
#define SEEPROM_ACCESS_HALFCLOCK_SHIFT  16      /* bits */
#define SEEPROM_ACCESS_ADDRESS_SIZE 16      /* bits */

#define SEEPROM_ACCESS_HALFCLOCK_340KHZ 0x0060      /* 340kHz */
#define SEEPROM_ACCESS_INIT     0x20600000  /* reset+clock  */

/*
 * "Linearised" address mask, treating multiple devices as consecutive
 */
#define SEEPROM_DEV_AND_ADDR_MASK   0x0007fffc  /* 8x64k devices */

/*
 * Non-Volatile Memory Interface Registers
 * Note: on chips that support the flash interface (5702+), flash is the
 * default and the legacy seeprom interface must be explicitly enabled
 * if required. On older chips (5700/01), SEEPROM is the default (and
 * only) non-volatile memory available, and these registers don't exist!
 */
#define NVM_FLASH_CMD_REG       0x7000
#define NVM_FLASH_CMD_LAST      0x00000100
#define NVM_FLASH_CMD_FIRST     0x00000080
#define NVM_FLASH_CMD_RD        0x00000000
#define NVM_FLASH_CMD_WR        0x00000020
#define NVM_FLASH_CMD_DOIT      0x00000010
#define NVM_FLASH_CMD_DONE      0x00000008

#define NVM_FLASH_WRITE_REG     0x7008
#define NVM_FLASH_READ_REG      0x7010

#define NVM_FLASH_ADDR_REG      0x700c
#define NVM_FLASH_ADDR_MASK     0x00fffffc

#define NVM_CONFIG1_REG         0x7014
#define NVM_CFG1_LEGACY_SEEPROM_MODE    0x80000000
#define NVM_CFG1_SEE_CLK_DIV_MASK   0x003ff800
#define NVM_CFG1_SPI_CLK_DIV_MASK   0x00000780
#define NVM_CFG1_BUFFERED_MODE      0x00000002
#define NVM_CFG1_FLASH_MODE     0x00000001

#define NVM_SW_ARBITRATION_REG      0x7020
#define NVM_READ_REQ3           0X00008000
#define NVM_READ_REQ2           0X00004000
#define NVM_READ_REQ1           0X00002000
#define NVM_READ_REQ0           0X00001000
#define NVM_WON_REQ3            0X00000800
#define NVM_WON_REQ2            0X00000400
#define NVM_WON_REQ1            0X00000200
#define NVM_WON_REQ0            0X00000100
#define NVM_RESET_REQ3          0X00000080
#define NVM_RESET_REQ2          0X00000040
#define NVM_RESET_REQ1          0X00000020
#define NVM_RESET_REQ0          0X00000010
#define NVM_SET_REQ3            0X00000008
#define NVM_SET_REQ2            0X00000004
#define NVM_SET_REQ1            0X00000002
#define NVM_SET_REQ0            0X00000001

/*
 * NVM access register
 * Applicable to BCM5721,BCM5751,BCM5752,BCM5714
 * and BCM5715 only.
 */
#define NVM_ACCESS_REG          0X7024
#define NVM_WRITE_ENABLE        0X00000002
#define NVM_ACCESS_ENABLE       0X00000001

/*
 * TLP Control Register
 * Applicable to BCM5721 and BCM5751 only
 */
#define TLP_CONTROL_REG         0x7c00
#define TLP_DATA_FIFO_PROTECT       0x02000000

/*
 * PHY Test Control Register
 * Applicable to BCM5721 and BCM5751 only
 */
#define PHY_TEST_CTRL_REG       0x7e2c
#define PHY_PCIE_SCRAM_MODE     0x20
#define PHY_PCIE_LTASS_MODE     0x40

/*
 * The internal firmware expects a certain layout of the non-volatile
 * memory (if fitted), and will check for it during startup, and use the
 * contents to initialise various internal parameters if it looks good.
 *
 * The offsets and field definitions below refer to where to find some
 * important values, and how to interpret them ...
 */
#define NVMEM_DATA_MAC_ADDRESS      0x007c      /* 8 bytes  */
#define NVMEM_DATA_MAC_ADDRESS_5906 0x0010      /* 8 bytes  */

/*
 * MII (PHY) registers, beyond those already defined in <sys/miiregs.h>
 */

#define MII_AN_LPNXTPG          8
#define MII_1000BASE_T_CONTROL      9
#define MII_1000BASE_T_STATUS       10
#define MII_IEEE_EXT_STATUS     15

/*
 * New bits in the MII_CONTROL register
 */
#define MII_CONTROL_1000MB      0x0040

/*
 * New bits in the MII_AN_ADVERT register
 */
#define MII_ABILITY_ASYM_PAUSE      0x0800
#define MII_ABILITY_PAUSE       0x0400

/*
 * Values for the <selector> field of the MII_AN_ADVERT register
 */
#define MII_AN_SELECTOR_8023        0x0001

/*
 * Bits in the MII_1000BASE_T_CONTROL register
 *
 * The MASTER_CFG bit enables manual configuration of Master/Slave mode
 * (otherwise, roles are automatically negotiated).  When this bit is set,
 * the MASTER_SEL bit forces Master mode, otherwise Slave mode is forced.
 */
#define MII_1000BT_CTL_MASTER_CFG   0x1000  /* enable role select   */
#define MII_1000BT_CTL_MASTER_SEL   0x0800  /* role select bit  */
#define MII_1000BT_CTL_ADV_FDX      0x0200
#define MII_1000BT_CTL_ADV_HDX      0x0100

/*
 * Bits in the MII_1000BASE_T_STATUS register
 */
#define MII_1000BT_STAT_MASTER_FAULT    0x8000
#define MII_1000BT_STAT_MASTER_MODE 0x4000  /* shows role selected  */
#define MII_1000BT_STAT_LCL_RCV_OK  0x2000
#define MII_1000BT_STAT_RMT_RCV_OK  0x1000
#define MII_1000BT_STAT_LP_FDX_CAP  0x0800
#define MII_1000BT_STAT_LP_HDX_CAP  0x0400

/*
 * Vendor-specific MII registers
 */
#define MII_EXT_CONTROL         MII_VENDOR(0)
#define MII_EXT_STATUS          MII_VENDOR(1)
#define MII_RCV_ERR_COUNT       MII_VENDOR(2)
#define MII_FALSE_CARR_COUNT        MII_VENDOR(3)
#define MII_RCV_NOT_OK_COUNT        MII_VENDOR(4)
#define MII_AUX_CONTROL         MII_VENDOR(8)
#define MII_AUX_STATUS          MII_VENDOR(9)
#define MII_INTR_STATUS         MII_VENDOR(10)
#define MII_INTR_MASK           MII_VENDOR(11)
#define MII_HCD_STATUS          MII_VENDOR(13)

#define MII_MAXREG          MII_VENDOR(15)  /* 31, 0x1f */

/*
 * Bits in the MII_EXT_CONTROL register
 */
#define MII_EXT_CTRL_INTERFACE_TBI  0x8000
#define MII_EXT_CTRL_DISABLE_AUTO_MDIX  0x4000
#define MII_EXT_CTRL_DISABLE_TRANSMIT   0x2000
#define MII_EXT_CTRL_DISABLE_INTERRUPT  0x1000
#define MII_EXT_CTRL_FORCE_INTERRUPT    0x0800
#define MII_EXT_CTRL_BYPASS_4B5B    0x0400
#define MII_EXT_CTRL_BYPASS_SCRAMBLER   0x0200
#define MII_EXT_CTRL_BYPASS_MLT3    0x0100
#define MII_EXT_CTRL_BYPASS_RX_ALIGN    0x0080
#define MII_EXT_CTRL_RESET_SCRAMBLER    0x0040
#define MII_EXT_CTRL_LED_TRAFFIC_MODE   0x0020
#define MII_EXT_CTRL_FORCE_LEDS_ON  0x0010
#define MII_EXT_CTRL_FORCE_LEDS_OFF 0x0008
#define MII_EXT_CTRL_EXTEND_TX_IPG  0x0004
#define MII_EXT_CTRL_3LINK_LED_MODE 0x0002
#define MII_EXT_CTRL_FIFO_ELASTICITY    0x0001

/*
 * Bits in the MII_EXT_STATUS register
 */
#define MII_EXT_STAT_S3MII_FIFO_ERROR   0x8000
#define MII_EXT_STAT_WIRESPEED_DOWNGRADE 0x4000
#define MII_EXT_STAT_MDIX_STATE     0x2000
#define MII_EXT_STAT_INTERRUPT_STATUS   0x1000
#define MII_EXT_STAT_REMOTE_RCVR_STATUS 0x0800
#define MII_EXT_STAT_LOCAL_RDVR_STATUS  0x0400
#define MII_EXT_STAT_DESCRAMBLER_LOCKED 0x0200
#define MII_EXT_STAT_LINK_STATUS    0x0100
#define MII_EXT_STAT_CRC_ERROR      0x0080
#define MII_EXT_STAT_CARR_EXT_ERROR 0x0040
#define MII_EXT_STAT_BAD_SSD_ERROR  0x0020
#define MII_EXT_STAT_BAD_ESD_ERROR  0x0010
#define MII_EXT_STAT_RECEIVE_ERROR  0x0008
#define MII_EXT_STAT_TRANSMIT_ERROR 0x0004
#define MII_EXT_STAT_LOCK_ERROR     0x0002
#define MII_EXT_STAT_MLT3_CODE_ERROR    0x0001

/*
 * The AUX CONTROL register is seriously weird!
 *
 * It hides (up to) eight 'shadow' registers.  When writing, which one
 * of them is written is determined by the low-order bits of the data
 * written(!), but when reading, which one is read is determined by the
 * value previously written to (part of) one of the shadow registers!!!
 */

/*
 * Shadow register numbers
 */
#define MII_AUX_CTRL_NORMAL     0
#define MII_AUX_CTRL_10BASE_T       1
#define MII_AUX_CTRL_POWER      2
#define MII_AUX_CTRL_TEST_1     4
#define MII_AUX_CTRL_MISC       7

/*
 * Selected bits in some of the shadow registers ...
 */
#define MII_AUX_CTRL_NORM_EXT_LOOPBACK  0x8000
#define MII_AUX_CTRL_NORM_LONG_PKTS 0x4000
#define MII_AUX_CTRL_NORM_EDGE_CTRL 0x3000
#define MII_AUX_CTRL_NORM_TX_MODE   0x0400
#define MII_AUX_CTRL_NORM_CABLE_TEST    0x0008

#define MII_AUX_CTRL_TEST_TX_HALF   0x0008

#define MII_AUX_CTRL_MISC_WRITE_ENABLE  0x8000
#define MII_AUX_CTRL_MISC_WIRE_SPEED    0x0010

/*
 * Write this value to the AUX control register
 * to select which shadow register will be read
 */
#define MII_AUX_CTRL_SHADOW_READ(x) (((x) << 12) | MII_AUX_CTRL_MISC)

/*
 * Bits in the MII_AUX_STATUS register
 */
#define MII_AUX_STATUS_MODE_MASK    0x0700
#define MII_AUX_STATUS_MODE_1000_F  0x0700
#define MII_AUX_STATUS_MODE_1000_H  0x0600
#define MII_AUX_STATUS_MODE_100_F   0x0500
#define MII_AUX_STATUS_MODE_100_4   0x0400
#define MII_AUX_STATUS_MODE_100_H   0x0300
#define MII_AUX_STATUS_MODE_10_F    0x0200
#define MII_AUX_STATUS_MODE_10_H    0x0100
#define MII_AUX_STATUS_MODE_NONE    0x0000
#define MII_AUX_STATUS_MODE_SHIFT   8

#define MII_AUX_STATUS_PAR_FAULT    0x0080
#define MII_AUX_STATUS_REM_FAULT    0x0040
#define MII_AUX_STATUS_LP_ANEG_ABLE 0x0010
#define MII_AUX_STATUS_LP_NP_ABLE   0x0008

#define MII_AUX_STATUS_LINKUP       0x0004
#define MII_AUX_STATUS_RX_PAUSE     0x0002
#define MII_AUX_STATUS_TX_PAUSE     0x0001

#define MII_AUX_STATUS_SPEED_IND_5906   0x0008
#define MII_AUX_STATUS_NEG_ENABLED_5906     0x0002
#define MII_AUX_STATUS_DUPLEX_IND_5906      0x0001

/*
 * Bits in the MII_INTR_STATUS and MII_INTR_MASK registers
 */
#define MII_INTR_RMT_RX_STATUS_CHANGE   0x0020
#define MII_INTR_LCL_RX_STATUS_CHANGE   0x0010
#define MII_INTR_LINK_DUPLEX_CHANGE 0x0008
#define MII_INTR_LINK_SPEED_CHANGE  0x0004
#define MII_INTR_LINK_STATUS_CHANGE 0x0002


/*
 * Third section:
 *  Hardware-defined data structures
 *
 * Note that the chip is naturally BIG-endian, so, for a big-endian
 * host, the structures defined below match those described in the PRM.
 * For little-endian hosts, some structures have to be swapped around.
 */

#if !defined(_BIG_ENDIAN) && !defined(_LITTLE_ENDIAN)
#error  Host endianness not defined
#endif

/*
 * Architectural constants: absolute maximum numbers of each type of ring
 */
#ifdef BGE_EXT_MEM
#define BGE_SEND_RINGS_MAX      16  /* only with ext mem    */
#else
#define BGE_SEND_RINGS_MAX      4
#endif
#define BGE_SEND_RINGS_MAX_5705     1
#define BGE_RECV_RINGS_MAX      16
#define BGE_RECV_RINGS_MAX_5705     1
#define BGE_BUFF_RINGS_MAX      3   /* jumbo/std/mini (mini */
                        /* only with ext mem)   */

#define BGE_SEND_SLOTS_MAX      512
#define BGE_STD_SLOTS_MAX       512
#define BGE_JUMBO_SLOTS_MAX     256
#define BGE_MINI_SLOTS_MAX      1024
#define BGE_RECV_SLOTS_MAX      2048
#define BGE_RECV_SLOTS_5705     512
#define BGE_RECV_SLOTS_5782     512
#define BGE_RECV_SLOTS_5721     512

/*
 * Hardware-defined Ring Control Block
 */
typedef struct {
    uint64_t    host_ring_addr;
#ifdef  _BIG_ENDIAN
    uint16_t    max_len;
    uint16_t    flags;
    uint32_t    nic_ring_addr;
#else
    uint32_t    nic_ring_addr;
    uint16_t    flags;
    uint16_t    max_len;
#endif  /* _BIG_ENDIAN */
} bge_rcb_t;

#define RCB_FLAG_USE_EXT_RCV_BD     0x0001
#define RCB_FLAG_RING_DISABLED      0x0002

/*
 * Hardware-defined Send Buffer Descriptor
 */
typedef struct {
    uint64_t    host_buf_addr;
#ifdef  _BIG_ENDIAN
    uint16_t    len;
    uint16_t    flags;
    uint16_t    reserved;
    uint16_t    vlan_tci;
#else
    uint16_t    vlan_tci;
    uint16_t    reserved;
    uint16_t    flags;
    uint16_t    len;
#endif  /* _BIG_ENDIAN */
} bge_sbd_t;

#define SBD_FLAG_TCP_UDP_CKSUM      0x0001
#define SBD_FLAG_IP_CKSUM       0x0002
#define SBD_FLAG_PACKET_END     0x0004
#define SBD_FLAG_IP_FRAG        0x0008
#define SBD_FLAG_IP_FRAG_END        0x0010

#define SBD_FLAG_VLAN_TAG       0x0040
#define SBD_FLAG_COAL_NOW       0x0080
#define SBD_FLAG_CPU_PRE_DMA        0x0100
#define SBD_FLAG_CPU_POST_DMA       0x0200

#define SBD_FLAG_INSERT_SRC_ADDR    0x1000
#define SBD_FLAG_CHOOSE_SRC_ADDR    0x6000
#define SBD_FLAG_DONT_GEN_CRC       0x8000

/*
 * Hardware-defined Receive Buffer Descriptor
 */
typedef struct {
    uint64_t    host_buf_addr;
#ifdef  _BIG_ENDIAN
    uint16_t    index;
    uint16_t    len;
    uint16_t    type;
    uint16_t    flags;
    uint16_t    ip_cksum;
    uint16_t    tcp_udp_cksum;
    uint16_t    error_flag;
    uint16_t    vlan_tci;
    uint32_t    reserved;
    uint32_t    opaque;
#else
    uint16_t    flags;
    uint16_t    type;
    uint16_t    len;
    uint16_t    index;
    uint16_t    vlan_tci;
    uint16_t    error_flag;
    uint16_t    tcp_udp_cksum;
    uint16_t    ip_cksum;
    uint32_t    opaque;
    uint32_t    reserved;
#endif  /* _BIG_ENDIAN */
} bge_rbd_t;

#define RBD_FLAG_STD_RING       0x0000
#define RBD_FLAG_PACKET_END     0x0004

#define RBD_FLAG_JUMBO_RING     0x0020
#define RBD_FLAG_VLAN_TAG       0x0040

#define RBD_FLAG_FRAME_HAS_ERROR    0x0400
#define RBD_FLAG_MINI_RING      0x0800
#define RBD_FLAG_IP_CHECKSUM        0x1000
#define RBD_FLAG_TCP_UDP_CHECKSUM   0x2000
#define RBD_FLAG_TCP_UDP_IS_TCP     0x4000

#define RBD_FLAG_DEFAULT        0x0000

#define RBD_ERROR_BAD_CRC       0x00010000
#define RBD_ERROR_COLL_DETECT       0x00020000
#define RBD_ERROR_LINK_LOST     0x00040000
#define RBD_ERROR_PHY_DECODE_ERR    0x00080000
#define RBD_ERROR_ODD_NIBBLE_RX_MII 0x00100000
#define RBD_ERROR_MAC_ABORT     0x00200000
#define RBD_ERROR_LEN_LESS_64       0x00400000
#define RBD_ERROR_TRUNC_NO_RES      0x00800000
#define RBD_ERROR_GIANT_PKT_RCVD    0x01000000

/*
 * Hardware-defined Status Block,Size of status block
 * is actually 0x50 bytes.Use 0x80 bytes for cache line
 * alignment.For BCM5705/5788/5721/5751/5752/5714
 * and 5715,there is only 1 recv and send ring index,but
 * driver defined 16 indexs here,please pay attention only
 * one ring is enabled in these chipsets.
 */
typedef struct {
    uint64_t    flags_n_tag;
    uint16_t    buff_cons_index[4];
    struct {
#ifdef  _BIG_ENDIAN
        uint16_t    send_cons_index;
        uint16_t    recv_prod_index;
#else
        uint16_t    recv_prod_index;
        uint16_t    send_cons_index;
#endif  /* _BIG_ENDIAN */
    } index[16];
} bge_status_t;

/*
 * Hardware-defined Receive BD Rule
 */
typedef struct {
    uint32_t    control;
    uint32_t    mask_value;
} bge_recv_rule_t;

/*
 * This describes which sub-rule slots are used by a particular rule.
 */
typedef struct {
    int     start;
    int     count;
} bge_rule_info_t;

/*
 * Indexes into the <buff_cons_index> array
 */
#ifdef  _BIG_ENDIAN
#define STATUS_STD_BUFF_CONS_INDEX  0
#define STATUS_JUMBO_BUFF_CONS_INDEX    1
#define STATUS_MINI_BUFF_CONS_INDEX 3
#define SEND_INDEX_P(bsp, ring) (&(bsp)->index[(ring)^0].send_cons_index)
#define RECV_INDEX_P(bsp, ring) (&(bsp)->index[(ring)^0].recv_prod_index)
#else
#define STATUS_STD_BUFF_CONS_INDEX  3
#define STATUS_JUMBO_BUFF_CONS_INDEX    2
#define STATUS_MINI_BUFF_CONS_INDEX 0
#define SEND_INDEX_P(bsp, ring) (&(bsp)->index[(ring)^1].send_cons_index)
#define RECV_INDEX_P(bsp, ring) (&(bsp)->index[(ring)^1].recv_prod_index)
#endif  /* _BIG_ENDIAN */

/*
 * Bits in the <flags_n_tag> word
 */
#define STATUS_FLAG_UPDATED     0x0000000100000000ull
#define STATUS_FLAG_LINK_CHANGED    0x0000000200000000ull
#define STATUS_FLAG_ERROR       0x0000000400000000ull
#define STATUS_TAG_MASK         0x00000000000000FFull

/*
 * The tag from the status block is fed back to Interrupt Mailbox 0
 * (INTERRUPT_MBOX_0_REG, 0x0200) after servicing an interrupt.  This
 * lets the chip know what updates have been processed, so it can
 * reassert its interrupt if more updates have occurred since.
 *
 * These macros extract the tag from the <flags_n_tag> word, shift
 * it to the proper position in the Mailbox register, and provide
 * the complete values to write to INTERRUPT_MBOX_0_REG to disable
 * or enable interrupts
 */
#define STATUS_TAG(fnt)         ((fnt) & STATUS_TAG_MASK)
#define INTERRUPT_TAG(fnt)      (STATUS_TAG(fnt) << 24)
#define INTERRUPT_MBOX_DISABLE(fnt) (INTERRUPT_TAG(fnt) | 1)
#define INTERRUPT_MBOX_ENABLE(fnt)  (INTERRUPT_TAG(fnt) | 0)

/*
 * Hardware-defined Statistics Block Offsets
 *
 * These are given in the manual as addresses in NIC memory, starting
 * from the NIC statistics area base address of 0x300; but here we
 * convert them into indexes into an array of (uint64_t)s, so we can
 * use them directly for accessing the copy of the statistics block
 * that the chip DMAs into main memory ...
 */

#define KS_BASE             0x300
#define KS_ADDR(x)          (((x)-KS_BASE)/sizeof (uint64_t))

typedef enum {
    KS_ifHCInOctets = KS_ADDR(0x400),
    KS_etherStatsFragments = KS_ADDR(0x410),
    KS_ifHCInUcastPkts,
    KS_ifHCInMulticastPkts,
    KS_ifHCInBroadcastPkts,
    KS_dot3StatsFCSErrors,
    KS_dot3StatsAlignmentErrors,
    KS_xonPauseFramesReceived,
    KS_xoffPauseFramesReceived,
    KS_macControlFramesReceived,
    KS_xoffStateEntered,
    KS_dot3StatsFrameTooLongs,
    KS_etherStatsJabbers,
    KS_etherStatsUndersizePkts,
    KS_inRangeLengthError,
    KS_outRangeLengthError,
    KS_etherStatsPkts64Octets,
    KS_etherStatsPkts65to127Octets,
    KS_etherStatsPkts128to255Octets,
    KS_etherStatsPkts256to511Octets,
    KS_etherStatsPkts512to1023Octets,
    KS_etherStatsPkts1024to1518Octets,
    KS_etherStatsPkts1519to2047Octets,
    KS_etherStatsPkts2048to4095Octets,
    KS_etherStatsPkts4096to8191Octets,
    KS_etherStatsPkts8192to9022Octets,

    KS_ifHCOutOctets = KS_ADDR(0x600),
    KS_etherStatsCollisions = KS_ADDR(0x610),
    KS_outXonSent,
    KS_outXoffSent,
    KS_flowControlDone,
    KS_dot3StatsInternalMacTransmitErrors,
    KS_dot3StatsSingleCollisionFrames,
    KS_dot3StatsMultipleCollisionFrames,
    KS_dot3StatsDeferredTransmissions,
    KS_dot3StatsExcessiveCollisions = KS_ADDR(0x658),
    KS_dot3StatsLateCollisions,
    KS_dot3Collided2Times,
    KS_dot3Collided3Times,
    KS_dot3Collided4Times,
    KS_dot3Collided5Times,
    KS_dot3Collided6Times,
    KS_dot3Collided7Times,
    KS_dot3Collided8Times,
    KS_dot3Collided9Times,
    KS_dot3Collided10Times,
    KS_dot3Collided11Times,
    KS_dot3Collided12Times,
    KS_dot3Collided13Times,
    KS_dot3Collided14Times,
    KS_dot3Collided15Times,
    KS_ifHCOutUcastPkts,
    KS_ifHCOutMulticastPkts,
    KS_ifHCOutBroadcastPkts,
    KS_dot3StatsCarrierSenseErrors,
    KS_ifOutDiscards,
    KS_ifOutErrors,

    KS_COSIfHCInPkts_1 = KS_ADDR(0x800),        /* [16] */
    KS_COSIfHCInPkts_2,
    KS_COSIfHCInPkts_3,
    KS_COSIfHCInPkts_4,
    KS_COSIfHCInPkts_5,
    KS_COSIfHCInPkts_6,
    KS_COSIfHCInPkts_7,
    KS_COSIfHCInPkts_8,
    KS_COSIfHCInPkts_9,
    KS_COSIfHCInPkts_10,
    KS_COSIfHCInPkts_11,
    KS_COSIfHCInPkts_12,
    KS_COSIfHCInPkts_13,
    KS_COSIfHCInPkts_14,
    KS_COSIfHCInPkts_15,
    KS_COSIfHCInPkts_16,
    KS_COSFramesDroppedDueToFilters,
    KS_nicDmaWriteQueueFull,
    KS_nicDmaWriteHighPriQueueFull,
    KS_nicNoMoreRxBDs,
    KS_ifInDiscards,
    KS_ifInErrors,
    KS_nicRecvThresholdHit,

    KS_COSIfHCOutPkts_1 = KS_ADDR(0x900),       /* [16] */
    KS_COSIfHCOutPkts_2,
    KS_COSIfHCOutPkts_3,
    KS_COSIfHCOutPkts_4,
    KS_COSIfHCOutPkts_5,
    KS_COSIfHCOutPkts_6,
    KS_COSIfHCOutPkts_7,
    KS_COSIfHCOutPkts_8,
    KS_COSIfHCOutPkts_9,
    KS_COSIfHCOutPkts_10,
    KS_COSIfHCOutPkts_11,
    KS_COSIfHCOutPkts_12,
    KS_COSIfHCOutPkts_13,
    KS_COSIfHCOutPkts_14,
    KS_COSIfHCOutPkts_15,
    KS_COSIfHCOutPkts_16,
    KS_nicDmaReadQueueFull,
    KS_nicDmaReadHighPriQueueFull,
    KS_nicSendDataCompQueueFull,
    KS_nicRingSetSendProdIndex,
    KS_nicRingStatusUpdate,
    KS_nicInterrupts,
    KS_nicAvoidedInterrupts,
    KS_nicSendThresholdHit,

    KS_STATS_SIZE = KS_ADDR(0xb00)
} bge_stats_offset_t;

/*
 * Hardware-defined Statistics Block
 *
 * Another view of the statistic block, as a array and a structure ...
 */

typedef union {
    uint64_t        a[KS_STATS_SIZE];
    struct {
        uint64_t    spare1[(0x400-0x300)/sizeof (uint64_t)];

        uint64_t    ifHCInOctets;       /* 0x0400   */
        uint64_t    spare2[1];
        uint64_t    etherStatsFragments;
        uint64_t    ifHCInUcastPkts;
        uint64_t    ifHCInMulticastPkts;
        uint64_t    ifHCInBroadcastPkts;
        uint64_t    dot3StatsFCSErrors;
        uint64_t    dot3StatsAlignmentErrors;
        uint64_t    xonPauseFramesReceived;
        uint64_t    xoffPauseFramesReceived;
        uint64_t    macControlFramesReceived;
        uint64_t    xoffStateEntered;
        uint64_t    dot3StatsFrameTooLongs;
        uint64_t    etherStatsJabbers;
        uint64_t    etherStatsUndersizePkts;
        uint64_t    inRangeLengthError;
        uint64_t    outRangeLengthError;
        uint64_t    etherStatsPkts64Octets;
        uint64_t    etherStatsPkts65to127Octets;
        uint64_t    etherStatsPkts128to255Octets;
        uint64_t    etherStatsPkts256to511Octets;
        uint64_t    etherStatsPkts512to1023Octets;
        uint64_t    etherStatsPkts1024to1518Octets;
        uint64_t    etherStatsPkts1519to2047Octets;
        uint64_t    etherStatsPkts2048to4095Octets;
        uint64_t    etherStatsPkts4096to8191Octets;
        uint64_t    etherStatsPkts8192to9022Octets;
        uint64_t    spare3[(0x600-0x4d8)/sizeof (uint64_t)];

        uint64_t    ifHCOutOctets;      /* 0x0600   */
        uint64_t    spare4[1];
        uint64_t    etherStatsCollisions;
        uint64_t    outXonSent;
        uint64_t    outXoffSent;
        uint64_t    flowControlDone;
        uint64_t    dot3StatsInternalMacTransmitErrors;
        uint64_t    dot3StatsSingleCollisionFrames;
        uint64_t    dot3StatsMultipleCollisionFrames;
        uint64_t    dot3StatsDeferredTransmissions;
        uint64_t    spare5[1];
        uint64_t    dot3StatsExcessiveCollisions;
        uint64_t    dot3StatsLateCollisions;
        uint64_t    dot3Collided2Times;
        uint64_t    dot3Collided3Times;
        uint64_t    dot3Collided4Times;
        uint64_t    dot3Collided5Times;
        uint64_t    dot3Collided6Times;
        uint64_t    dot3Collided7Times;
        uint64_t    dot3Collided8Times;
        uint64_t    dot3Collided9Times;
        uint64_t    dot3Collided10Times;
        uint64_t    dot3Collided11Times;
        uint64_t    dot3Collided12Times;
        uint64_t    dot3Collided13Times;
        uint64_t    dot3Collided14Times;
        uint64_t    dot3Collided15Times;
        uint64_t    ifHCOutUcastPkts;
        uint64_t    ifHCOutMulticastPkts;
        uint64_t    ifHCOutBroadcastPkts;
        uint64_t    dot3StatsCarrierSenseErrors;
        uint64_t    ifOutDiscards;
        uint64_t    ifOutErrors;
        uint64_t    spare6[(0x800-0x708)/sizeof (uint64_t)];

        uint64_t    COSIfHCInPkts[16];  /* 0x0800   */
        uint64_t    COSFramesDroppedDueToFilters;
        uint64_t    nicDmaWriteQueueFull;
        uint64_t    nicDmaWriteHighPriQueueFull;
        uint64_t    nicNoMoreRxBDs;
        uint64_t    ifInDiscards;
        uint64_t    ifInErrors;
        uint64_t    nicRecvThresholdHit;
        uint64_t    spare7[(0x900-0x8b8)/sizeof (uint64_t)];

        uint64_t    COSIfHCOutPkts[16]; /* 0x0900   */
        uint64_t    nicDmaReadQueueFull;
        uint64_t    nicDmaReadHighPriQueueFull;
        uint64_t    nicSendDataCompQueueFull;
        uint64_t    nicRingSetSendProdIndex;
        uint64_t    nicRingStatusUpdate;
        uint64_t    nicInterrupts;
        uint64_t    nicAvoidedInterrupts;
        uint64_t    nicSendThresholdHit;
        uint64_t    spare8[(0xb00-0x9c0)/sizeof (uint64_t)];
    } s;
} bge_statistics_t;

#define KS_STAT_REG_SIZE    (0x1B)
#define KS_STAT_REG_BASE    (0x800)

typedef struct {
    uint32_t    ifHCOutOctets;
    uint32_t    etherStatsCollisions;
    uint32_t    outXonSent;
    uint32_t    outXoffSent;
    uint32_t    dot3StatsInternalMacTransmitErrors;
    uint32_t    dot3StatsSingleCollisionFrames;
    uint32_t    dot3StatsMultipleCollisionFrames;
    uint32_t    dot3StatsDeferredTransmissions;
    uint32_t    dot3StatsExcessiveCollisions;
    uint32_t    dot3StatsLateCollisions;
    uint32_t    ifHCOutUcastPkts;
    uint32_t    ifHCOutMulticastPkts;
    uint32_t    ifHCOutBroadcastPkts;
    uint32_t    ifHCInOctets;
    uint32_t    etherStatsFragments;
    uint32_t    ifHCInUcastPkts;
    uint32_t    ifHCInMulticastPkts;
    uint32_t    ifHCInBroadcastPkts;
    uint32_t    dot3StatsFCSErrors;
    uint32_t    dot3StatsAlignmentErrors;
    uint32_t    xonPauseFramesReceived;
    uint32_t    xoffPauseFramesReceived;
    uint32_t    macControlFramesReceived;
    uint32_t    xoffStateEntered;
    uint32_t    dot3StatsFrameTooLongs;
    uint32_t    etherStatsJabbers;
    uint32_t    etherStatsUndersizePkts;
} bge_statistics_reg_t;


#ifdef BGE_IPMI_ASF

/*
 * Device internal memory entries
 */

#define BGE_FIRMWARE_MAILBOX                0x0b50
#define BGE_MAGIC_NUM_FIRMWARE_INIT_DONE        0x4b657654
#define BGE_MAGIC_NUM_DISABLE_DMAW_ON_LINK_CHANGE   0x4861764b


#define BGE_NIC_DATA_SIG_ADDR           0x0b54
#define BGE_NIC_DATA_SIG            0x4b657654


#define BGE_NIC_DATA_NIC_CFG_ADDR       0x0b58

#define BGE_NIC_CFG_LED_MODE_TRIPLE_SPEED   0x000004
#define BGE_NIC_CFG_LED_MODE_LINK_SPEED     0x000008
#define BGE_NIC_CFG_LED_MODE_OPEN_DRAIN     0x000004
#define BGE_NIC_CFG_LED_MODE_OUTPUT     0x000008
#define BGE_NIC_CFG_LED_MODE_MASK       0x00000c

#define BGE_NIC_CFG_PHY_TYPE_UNKNOWN        0x000000
#define BGE_NIC_CFG_PHY_TYPE_COPPER     0x000010
#define BGE_NIC_CFG_PHY_TYPE_FIBER      0x000020
#define BGE_NIC_CFG_PHY_TYPE_MASK       0x000030

#define BGE_NIC_CFG_ENABLE_WOL          0x000040
#define BGE_NIC_CFG_ENABLE_ASF          0x000080
#define BGE_NIC_CFG_EEPROM_WP           0x000100
#define BGE_NIC_CFG_POWER_SAVING        0x000200
#define BGE_NIC_CFG_SWAP_PORT           0x000800
#define BGE_NIC_CFG_MINI_PCI            0x001000
#define BGE_NIC_CFG_FIBER_WOL_CAPABLE       0x004000
#define BGE_NIC_CFG_5753_12x12          0x100000


#define BGE_NIC_DATA_FIRMWARE_VERSION       0x0b5c


#define BGE_NIC_DATA_PHY_ID_ADDR        0x0b74
#define BGE_NIC_PHY_ID1_MASK            0xffff0000
#define BGE_NIC_PHY_ID2_MASK            0x0000ffff


#define BGE_CMD_MAILBOX             0x0b78
#define BGE_CMD_NICDRV_ALIVE            0x00000001
#define BGE_CMD_NICDRV_PAUSE_FW         0x00000002
#define BGE_CMD_NICDRV_IPV4ADDR_CHANGE      0x00000003
#define BGE_CMD_NICDRV_IPV6ADDR_CHANGE      0x00000004


#define BGE_CMD_LENGTH_MAILBOX          0x0b7c
#define BGE_CMD_DATA_MAILBOX            0x0b80
#define BGE_ASF_FW_STATUS_MAILBOX       0x0c00

#define BGE_DRV_STATE_MAILBOX           0x0c04
#define BGE_DRV_STATE_START         0x00000001
#define BGE_DRV_STATE_START_DONE        0x80000001
#define BGE_DRV_STATE_UNLOAD            0x00000002
#define BGE_DRV_STATE_UNLOAD_DONE       0x80000002
#define BGE_DRV_STATE_WOL           0x00000003
#define BGE_DRV_STATE_SUSPEND           0x00000004


#define BGE_FW_LAST_RESET_TYPE_MAILBOX      0x0c08
#define BGE_FW_LAST_RESET_TYPE_WARM     0x0001
#define BGE_FW_LAST_RESET_TYPE_COLD     0x0002


#define BGE_MAC_ADDR_HIGH_MAILBOX       0x0c14
#define BGE_MAC_ADDR_LOW_MAILBOX        0x0c18


/*
 * RX-RISC event register
 */
#define RX_RISC_EVENT_REG           0x6810
#define RRER_ASF_EVENT              0x4000

#endif /* BGE_IPMI_ASF */

#ifdef __cplusplus
}
#endif

#endif  /* _BGE_HW_H */