/*-
* Copyright (c) 1991 The Regents of the University of California.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 4. Neither the name of the University nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* from: @(#)ns16550.h 7.1 (Berkeley) 5/9/91
* $FreeBSD$
*/
/*
* NS8250... UART registers.
*/
/* 8250 registers #[0-6]. */
#define com_data 0 /* data register (R/W) */
#define REG_DATA com_data
#define com_ier 1 /* interrupt enable register (W) */
#define REG_IER com_ier
#define IER_ERXRDY 0x1
#define IER_ETXRDY 0x2
#define IER_ERLS 0x4
#define IER_EMSC 0x8
#define IER_BITS "\20\1ERXRDY\2ETXRDY\3ERLS\4EMSC"
#define com_iir 2 /* interrupt identification register (R) */
#define REG_IIR com_iir
#define IIR_IMASK 0xf
#define IIR_RXTOUT 0xc
#define IIR_BUSY 0x7
#define IIR_RLS 0x6
#define IIR_RXRDY 0x4
#define IIR_TXRDY 0x2
#define IIR_NOPEND 0x1
#define IIR_MLSC 0x0
#define IIR_FIFO_MASK 0xc0 /* set if FIFOs are enabled */
#define IIR_BITS "\20\1NOPEND\2TXRDY\3RXRDY"
#define com_lcr 3 /* line control register (R/W) */
#define com_cfcr com_lcr /* character format control register (R/W) */
#define REG_LCR com_lcr
#define LCR_DLAB 0x80
#define CFCR_DLAB LCR_DLAB
#define LCR_EFR_ENABLE 0xbf /* magic to enable EFR on 16650 up */
#define CFCR_EFR_ENABLE LCR_EFR_ENABLE
#define LCR_SBREAK 0x40
#define CFCR_SBREAK LCR_SBREAK
#define LCR_PZERO 0x30
#define CFCR_PZERO LCR_PZERO
#define LCR_PONE 0x20
#define CFCR_PONE LCR_PONE
#define LCR_PEVEN 0x10
#define CFCR_PEVEN LCR_PEVEN
#define LCR_PODD 0x00
#define CFCR_PODD LCR_PODD
#define LCR_PENAB 0x08
#define CFCR_PENAB LCR_PENAB
#define LCR_STOPB 0x04
#define CFCR_STOPB LCR_STOPB
#define LCR_8BITS 0x03
#define CFCR_8BITS LCR_8BITS
#define LCR_7BITS 0x02
#define CFCR_7BITS LCR_7BITS
#define LCR_6BITS 0x01
#define CFCR_6BITS LCR_6BITS
#define LCR_5BITS 0x00
#define CFCR_5BITS LCR_5BITS
#define com_mcr 4 /* modem control register (R/W) */
#define REG_MCR com_mcr
#define MCR_PRESCALE 0x80 /* only available on 16650 up */
#define MCR_LOOPBACK 0x10
#define MCR_IE 0x08
#define MCR_IENABLE MCR_IE
#define MCR_DRS 0x04
#define MCR_RTS 0x02
#define MCR_DTR 0x01
#define MCR_BITS "\20\1DTR\2RTS\3DRS\4IE\5LOOPBACK\10PRESCALE"
#define com_lsr 5 /* line status register (R/W) */
#define REG_LSR com_lsr
#define LSR_RCV_FIFO 0x80
#define LSR_TEMT 0x40
#define LSR_TSRE LSR_TEMT
#define LSR_THRE 0x20
#define LSR_TXRDY LSR_THRE
#define LSR_BI 0x10
#define LSR_FE 0x08
#define LSR_PE 0x04
#define LSR_OE 0x02
#define LSR_RXRDY 0x01
#define LSR_RCV_MASK 0x1f
#define LSR_BITS "\20\1RXRDY\2OE\3PE\4FE\5BI\6THRE\7TEMT\10RCV_FIFO"
#define com_msr 6 /* modem status register (R/W) */
#define REG_MSR com_msr
#define MSR_DCD 0x80
#define MSR_RI 0x40
#define MSR_DSR 0x20
#define MSR_CTS 0x10
#define MSR_DDCD 0x08
#define MSR_TERI 0x04
#define MSR_DDSR 0x02
#define MSR_DCTS 0x01
#define MSR_BITS "\20\1DCTS\2DDSR\3TERI\4DDCD\5CTS\6DSR\7RI\10DCD"
/* 8250 multiplexed registers #[0-1]. Access enabled by LCR[7]. */
#define com_dll 0 /* divisor latch low (R/W) */
#define com_dlbl com_dll
#define com_dlm 1 /* divisor latch high (R/W) */
#define com_dlbh com_dlm
#define REG_DLL com_dll
#define REG_DLH com_dlm
/* 16450 register #7. Not multiplexed. */
#define com_scr 7 /* scratch register (R/W) */
/* 16550 register #2. Not multiplexed. */
#define com_fcr 2 /* FIFO control register (W) */
#define com_fifo com_fcr
#define REG_FCR com_fcr
#define FCR_ENABLE 0x01
#define FIFO_ENABLE FCR_ENABLE
#define FCR_RCV_RST 0x02
#define FIFO_RCV_RST FCR_RCV_RST
#define FCR_XMT_RST 0x04
#define FIFO_XMT_RST FCR_XMT_RST
#define FCR_DMA 0x08
#define FIFO_DMA_MODE FCR_DMA
#define FCR_RX_LOW 0x00
#define FIFO_RX_LOW FCR_RX_LOW
#define FCR_RX_MEDL 0x40
#define FIFO_RX_MEDL FCR_RX_MEDL
#define FCR_RX_MEDH 0x80
#define FIFO_RX_MEDH FCR_RX_MEDH
#define FCR_RX_HIGH 0xc0
#define FIFO_RX_HIGH FCR_RX_HIGH
#define FCR_BITS "\20\1ENABLE\2RCV_RST\3XMT_RST\4DMA"
/* 16650 registers #2,[4-7]. Access enabled by LCR_EFR_ENABLE. */
#define com_efr 2 /* enhanced features register (R/W) */
#define REG_EFR com_efr
#define EFR_CTS 0x80
#define EFR_AUTOCTS EFR_CTS
#define EFR_RTS 0x40
#define EFR_AUTORTS EFR_RTS
#define EFR_EFE 0x10 /* enhanced functions enable */
#define com_xon1 4 /* XON 1 character (R/W) */
#define com_xon2 5 /* XON 2 character (R/W) */
#define com_xoff1 6 /* XOFF 1 character (R/W) */
#define com_xoff2 7 /* XOFF 2 character (R/W) */
#define DW_REG_USR 31 /* DesignWare derived Uart Status Reg */
#define com_usr 39 /* Octeon 16750/16550 Uart Status Reg */
#define REG_USR com_usr
#define USR_BUSY 1 /* Uart Busy. Serial transfer in progress */
#define USR_TXFIFO_NOTFULL 2 /* Uart TX FIFO Not full */
/* 16950 register #1. Access enabled by ACR[7]. Also requires !LCR[7]. */
#define com_asr 1 /* additional status register (R[0-7]/W[0-1]) */
/* 16950 register #3. R/W access enabled by ACR[7]. */
#define com_rfl 3 /* receiver fifo level (R) */
/*
* 16950 register #4. Access enabled by ACR[7]. Also requires
* !LCR_EFR_ENABLE.
*/
#define com_tfl 4 /* transmitter fifo level (R) */
/*
* 16950 register #5. Accessible if !LCR_EFR_ENABLE. Read access also
* requires ACR[6].
*/
#define com_icr 5 /* index control register (R/W) */
/*
* 16950 register #7. It is the same as com_scr except it has a different
* abbreviation in the manufacturer's data sheet and it also serves as an
* index into the Indexed Control register set.
*/
#define com_spr com_scr /* scratch pad (and index) register (R/W) */
#define REG_SPR com_scr
/*
* 16950 indexed control registers #[0-0x13]. Access is via index in SPR,
* data in ICR (if ICR is accessible).
*/
#define com_acr 0 /* additional control register (R/W) */
#define ACR_ASE 0x80 /* ASR/RFL/TFL enable */
#define ACR_ICRE 0x40 /* ICR enable */
#define ACR_TLE 0x20 /* TTL/RTL enable */
#define com_cpr 1 /* clock prescaler register (R/W) */
#define com_tcr 2 /* times clock register (R/W) */
#define com_ttl 4 /* transmitter trigger level (R/W) */
#define com_rtl 5 /* receiver trigger level (R/W) */
/* ... */
/* Hardware extension mode register for RSB-2000/3000. */
#define com_emr com_msr
#define EMR_EXBUFF 0x04
#define EMR_CTSFLW 0x08
#define EMR_DSRFLW 0x10
#define EMR_RTSFLW 0x20
#define EMR_DTRFLW 0x40
#define EMR_EFMODE 0x80