Lines Matching refs:DEBUGOUT
130 #define DEBUGFUNC(F) DEBUGOUT(F "\n");
135 #define DEBUGOUT(S) printf(S)
141 #define DEBUGOUT(S)
357 DEBUGOUT("Could not acquire EEPROM grant\n");
513 DEBUGOUT("SPI EEPROM Status error\n");
544 DEBUGOUT("\"words\" parameter out of bounds\n");
620 DEBUGOUT("EEPROM Read Error\n");
629 DEBUGOUT("EEPROM Checksum Invalid\n");
652 DEBUGOUT("EEPROM Read Error\n");
684 DEBUGOUT("Programming MAC Address into RAR[0]\n");
696 DEBUGOUT("Clearing RAR[1-15]\n");
977 DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
982 DEBUGOUT("Masking off all interrupts\n");
1014 DEBUGOUT("Issuing a global reset to MAC\n");
1080 DEBUGOUT("Masking off all interrupts\n");
1124 DEBUGOUT("Initializing the IEEE VLAN\n");
1131 DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
1155 DEBUGOUT("Zeroing the MTA\n");
1292 DEBUGOUT("EEPROM Read Error\n");
1353 DEBUGOUT("Initializing the Flow Control address, type and timer regs\n");
1478 DEBUGOUT("Flow control param set incorrectly\n");
1489 DEBUGOUT("Auto-negotiation enabled\n");
1506 DEBUGOUT("Looking for Link\n");
1513 DEBUGOUT("Never got a valid link from auto-neg!!!\n");
1521 DEBUGOUT("Error while checking for link\n");
1527 DEBUGOUT("Valid Link Found\n");
1530 DEBUGOUT("No Signal Detected\n");
1567 DEBUGOUT("Error, did not detect valid phy.\n");
1585 DEBUGOUT("Error Resetting the PHY\n");
1595 DEBUGOUT("Error Disabling LPLU D3\n");
1769 DEBUGOUT("Error Resetting the PHY\n");
1802 DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
1804 DEBUGOUT("Error Setting up Auto-Negotiation\n");
1807 DEBUGOUT("Restarting Auto-Neg\n");
1825 DEBUGOUT("Error while waiting for autoneg to complete\n");
1834 DEBUGOUT("Error while waiting for autoneg to complete\n");
1862 DEBUGOUT("Error configuring MAC to PHY settings\n");
1867 DEBUGOUT("Error Configuring Flow Control\n");
1873 DEBUGOUT("Error Configuring DSP after link up\n");
1878 DEBUGOUT("Valid link established!!!\n");
1884 DEBUGOUT("Unable to establish link!!!\n");
1929 DEBUGOUT("Advertise 10mb Half duplex\n");
1935 DEBUGOUT("Advertise 10mb Full duplex\n");
1941 DEBUGOUT("Advertise 100mb Half duplex\n");
1947 DEBUGOUT("Advertise 100mb Full duplex\n");
1953 DEBUGOUT("Advertise 1000mb Half duplex requested, request denied!\n");
1958 DEBUGOUT("Advertise 1000mb Full duplex\n");
2011 DEBUGOUT("Flow control param set incorrectly\n");
2174 DEBUGOUT("Flow control param set incorrectly\n");
2216 DEBUGOUT("Error forcing flow control settings\n");
2298 DEBUGOUT("Flow Control = FULL.\r\n");
2301 DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
2317 DEBUGOUT("Flow Control = TX PAUSE frames only.\r\n");
2332 DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
2359 DEBUGOUT("Flow Control = NONE.\r\n");
2363 DEBUGOUT("Flow Control = NONE.\r\n");
2366 DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
2382 DEBUGOUT("Error forcing flow control settings\n");
2386 DEBUGOUT("Copper PHY and Auto Neg has not completed.\r\n");
2466 DEBUGOUT("Error configuring MAC to PHY settings\n");
2476 DEBUGOUT("Error configuring flow control\n");
2539 DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\r\n");
2551 DEBUGOUT("Error configuring flow control\n");
2564 DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\r\n");
2579 DEBUGOUT("SERDES: Link is up.\n");
2583 DEBUGOUT("SERDES: Link is down.\n");
2610 DEBUGOUT("1000 Mbs, ");
2613 DEBUGOUT("100 Mbs, ");
2616 DEBUGOUT("10 Mbs, ");
2621 DEBUGOUT("Full Duplex\r\n");
2624 DEBUGOUT(" Half Duplex\r\n");
2627 DEBUGOUT("1000 Mbs, Full Duplex\r\n");
2646 DEBUGOUT("Waiting for Auto-Neg to complete.\n");
2658 DEBUGOUT("Auto-Neg complete.\n");
2663 DEBUGOUT("Auto-Neg timedout.\n");
2868 DEBUGOUT("MDI Read did not complete\n");
2872 DEBUGOUT("MDI Error\n");
2972 DEBUGOUT("MDI Write did not complete\n");
3012 DEBUGOUT("Resetting Phy...\n");