Makefile revision 5680
1124N/A# The contents of this file are subject to the terms of the 1340N/A# Common Development and Distribution License (the "License"). 1276N/A# You may not use this file except in compliance with the License. 158N/A# See the License for the specific language governing permissions 158N/A# and limitations under the License. 158N/A# When distributing Covered Code, include this CDDL HEADER in each 158N/A# If applicable, add the following below this CDDL HEADER, with the 1276N/A# fields enclosed by brackets "[]" replaced with your own identifying 1340N/A# information: Portions Copyright [yyyy] [name of copyright owner] 158N/A# Copyright (c) 2011, 2016, Oracle and/or its affiliates. All rights reserved. # Need to preserve timestamp for Grammar files. If the pickle files are older, # Python will try to rebuild them. # We patch auto* files, so regenerate headers and configure # we don't want to leak $(CC_BITS) into BASECFLAGS as it causes problems with # to find the ncurses headers # enable large files how they did in JDS # because python links with $(CC) ... $(LDFLAGS) ... # The python build is profile-guided for studio; to see the benefits of that, # Python must be compiled with -xO5 and a different build target must be used. # Use of xprofile requires that the same options be used during compilation and # linking. The targets chosen are based on Solaris 11 minimum supported system # Python puts its header files in a special place. # PYTHONPATH in the environment can be harmful, but setting it to empty via # _INSTALL_ENV causes problems too, so just ignore the entire environment. # Because of this, we need to specify PATH in multiple places below. # 64 bit shared objects need to go in a 64-bit directory # Simplify the definitions of CC, CXX, CFLAGS and LDFLAGS so they hard-code # neither paths from our build systems nor Studio-specific options. (cd $(@D) ; $(GSED) -i -e 's/^CC=.*/CC=\t\tcc/' \ -e 's/^CXX=.*/CXX=\t\tCC/' \ -e 's/^CFLAGS=.*/CFLAGS=\t\t\$$\(BASECFLAGS) \$$\(OPT) \$$\(EXTRA_CFLAGS)/' \ -e 's|^LDFLAGS=.*|LDFLAGS=|' \ # Because we stripped the Makefile above, we need to pass several things in the # environment, and use -e to tell gmake to pay attention to the environment. # 1. Setup pyconfig.h file to support 32 & 64 bit. # related *.txt files in the same directory, it will rebuild them any time # you try to build a Python module. So here we also touch the pickle files # Note that although the 64-bit version is not used (and thus commented # out in the manifest), we still need to specify the 32-/64-bit paths, # otherwise the 64-bit build will fail to find the 32-bit path. $(GSED) -i -e 's|$(SOURCE_DIR)|.|g' -e 's|$(COMPONENT_DIR)|..|g' \ # Using "-uall,-network" ensures all tests are run except the network tests. # The network tests contain many expected failures when run behind a firewall. # The "-v" ensures verbose mode. You can set TESTOPTS_PYTHON_TEST to a # particular test if you want to run just one test. For example, run gmake with # "-k" so it continues and does both 32-bit and 64-bit tests, even if there is a # $ TESTOPTS_PYTHON_TEST=test_sys gmake -k test # Note that when a test succeeds, the builds/*/.tested file gets created. You # may need to remove these files, or run "gmake clobber" or "gmake clean" # The distutils tests need $CC in $PATH. # The test output contains details from each test, in whatever order they # complete. The default _TRANSFORMER is not powerful enough to deal with # this; we need heavier artillery. Extract just the sections that start # with "tests OK." and end with "Makefile: " for comparison.