i2c/clients/adm1026.c

	adm1026.c revision 193974072f41a843678abf5f61979c748687e66b
/*
 * CDDL HEADER START
 *
 * The contents of this file are subject to the terms of the
 * Common Development and Distribution License (the "License").
 * You may not use this file except in compliance with the License.
 *
 * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
 * or http://www.opensolaris.org/os/licensing.
 * See the License for the specific language governing permissions
 * and limitations under the License.
 *
 * When distributing Covered Code, include this CDDL HEADER in each
 * file and include the License file at usr/src/OPENSOLARIS.LICENSE.
 * If applicable, add the following below this CDDL HEADER, with the
 * fields enclosed by brackets "[]" replaced with your own identifying
 * information: Portions Copyright [yyyy] [name of copyright owner]
 *
 * CDDL HEADER END
 */
/*
 * Copyright 2008 Sun Microsystems, Inc.  All rights reserved.
 * Use is subject to license terms.
 */


#include <sys/stat.h>       /* ddi_create_minor_node S_IFCHR */
#include <sys/modctl.h>     /* for modldrv */
#include <sys/open.h>       /* for open params.  */
#include <sys/types.h>
#include <sys/kmem.h>
#include <sys/sunddi.h>
#include <sys/conf.h>       /* req. by dev_ops flags MTSAFE etc. */
#include <sys/ddi.h>
#include <sys/file.h>
#include <sys/note.h>
#include <sys/i2c/clients/i2c_gpio.h>
#include <sys/i2c/clients/adm1026_impl.h>

/*
 * This driver supports the GPIO subset of the full ADM1026 register set.
 * The driver is designed to allow modifying and reading the Polarity and
 * Direction bits of the ADM1026's 16 GPIO pins via the 4 GPIO Config
 * registers.  In addition, the driver supports modifying and reading
 * the 16 GPIO pins via the 2 GPIO input/output registers.
 *
 * The 4 GPIO Config registers configure the direction and polarity of
 * the 16 GPIO pins.  When a Polarity bit is set to 0, the GPIO pin is
 * active low, otherwise, it is active high.  When a Direction bit is set
 * to 0, the GPIO pin configured as an input; otherwise, it is an output.
 *
 * The 2 GPIO input/output registers (Status Register 5 & 6 ) behave as follows.
 * When a GPIO pin is configured as an input, the bit is set when its GPIO
 * pin is asserted.  When a GPIO pin is configured as an output, the bit
 * asserts the GPIO pin.
 *
 * The commands supported in the ioctl routine are:
 * GPIO_GET_OUTPUT   -- Read GPIO0-GPIO15 bits in Status Register 5 & 6
 * GPIO_SET_OUTPUT   -- Modify GPIO0-GPIO15 bits in Status Register 5 & 6
 * GPIO_GET_POLARITY -- Read GPIO0-GPIO15 Polarity bits in GPIO Config 1-4
 * GPIO_SET_POLARITY -- Modify GPIO0-GPIO15 Polarity bits in GPIO Config 1-4
 * GPIO_GET_CONFIG   -- Read GPIO0-GPIO15 Direction bits in GPIO Config 1-4
 * GPIO_SET_CONFIG   -- Modify GPIO0-GPIO15 Direction bits in GPIO Config 1-4
 *
 * A pointer to the i2c_gpio_t data structure is sent as the third argument
 * in the ioctl call.  The reg_mask and reg_val members of i2c_gpio_t are
 * used to logically represent the 16 GPIO pins, thus only the lower 16 bits
 * of each member is used.  The reg_mask member identifies the GPIO pin(s)
 * that the user wants to read or modify and reg_val has the actual value of
 * what the corresponding GPIO pin should be set to.
 *
 * For example, a reg_mask of 0x8001 indicates that the ioctl should only
 * access GPIO15 and GPIO0.
 */

static void *adm1026soft_statep;

static int adm1026_do_attach(dev_info_t *);
static int adm1026_do_detach(dev_info_t *);
static int adm1026_do_resume(void);
static int adm1026_do_suspend(void);
static int adm1026_get8(adm1026_unit_t *unitp, uint8_t reg, uint8_t *val);
static int adm1026_put8(adm1026_unit_t *unitp, uint8_t reg, uint8_t val);

/*
 * cb ops (only need ioctl)
 */
static int adm1026_open(dev_t *, int, int, cred_t *);
static int adm1026_close(dev_t, int, int, cred_t *);
static int adm1026_ioctl(dev_t, int, intptr_t, int, cred_t *, int *);

static struct cb_ops adm1026_cbops = {
    adm1026_open,           /* open  */
    adm1026_close,          /* close */
    nodev,              /* strategy */
    nodev,              /* print */
    nodev,              /* dump */
    nodev,              /* read */
    nodev,              /* write */
    adm1026_ioctl,          /* ioctl */
    nodev,              /* devmap */
    nodev,              /* mmap */
    nodev,              /* segmap */
    nochpoll,           /* poll */
    ddi_prop_op,            /* cb_prop_op */
    NULL,               /* streamtab */
    D_NEW | D_MP | D_HOTPLUG,   /* Driver compatibility flag */
    CB_REV,             /* rev */
    nodev,              /* int (*cb_aread)() */
    nodev               /* int (*cb_awrite)() */
};

/*
 * dev ops
 */
static int adm1026_attach(dev_info_t *dip, ddi_attach_cmd_t cmd);
static int adm1026_detach(dev_info_t *dip, ddi_detach_cmd_t cmd);

static struct dev_ops adm1026_ops = {
    DEVO_REV,
    0,
    ddi_getinfo_1to1,
    nulldev,
    nulldev,
    adm1026_attach,
    adm1026_detach,
    nodev,
    &adm1026_cbops,
    NULL,
    NULL,
    ddi_quiesce_not_needed,     /* quiesce */
};

extern struct mod_ops mod_driverops;

static struct modldrv adm1026_modldrv = {
    &mod_driverops,         /* type of module - driver */
    "ADM1026 i2c device driver: 1.3",
    &adm1026_ops
};

static struct modlinkage adm1026_modlinkage = {
    MODREV_1,
    &adm1026_modldrv,
    0
};


int
_init(void)
{
    int error;

    error = mod_install(&adm1026_modlinkage);

    if (!error)
        (void) ddi_soft_state_init(&adm1026soft_statep,
            sizeof (struct adm1026_unit), 1);
    return (error);
}

int
_fini(void)
{
    int error;

    error = mod_remove(&adm1026_modlinkage);
    if (!error)
        ddi_soft_state_fini(&adm1026soft_statep);

    return (error);
}

int
_info(struct modinfo *modinfop)
{
    return (mod_info(&adm1026_modlinkage, modinfop));
}

static int
adm1026_open(dev_t *devp, int flags, int otyp, cred_t *credp)
{
    _NOTE(ARGUNUSED(credp))

    adm1026_unit_t *unitp;
    int instance;
    int error = 0;

    instance = getminor(*devp);

    D2CMN_ERR((CE_WARN, "adm1026_open: instance=%d\n", instance));

    if (instance < 0) {
        return (ENXIO);
    }

    unitp = (struct adm1026_unit *)
        ddi_get_soft_state(adm1026soft_statep, instance);

    if (unitp == NULL) {
        return (ENXIO);
    }

    if (otyp != OTYP_CHR) {
        return (EINVAL);
    }

    mutex_enter(&unitp->adm1026_mutex);

    if (flags & FEXCL) {
        if (unitp->adm1026_oflag != 0) {
            error = EBUSY;
        } else {
            unitp->adm1026_oflag = FEXCL;
        }
    } else {
        if (unitp->adm1026_oflag == FEXCL) {
            error = EBUSY;
        } else {
            unitp->adm1026_oflag = FOPEN;
        }
    }

    mutex_exit(&unitp->adm1026_mutex);

    return (error);
}

static int
adm1026_close(dev_t dev, int flags, int otyp, cred_t *credp)
{
    _NOTE(ARGUNUSED(flags, otyp, credp))

    adm1026_unit_t *unitp;
    int instance;

    instance = getminor(dev);

    D2CMN_ERR((CE_WARN, "adm1026_close: instance=%d\n", instance));

    if (instance < 0) {
        return (ENXIO);
    }

    unitp = (struct adm1026_unit *)
        ddi_get_soft_state(adm1026soft_statep, instance);

    if (unitp == NULL) {
        return (ENXIO);
    }

    mutex_enter(&unitp->adm1026_mutex);

    unitp->adm1026_oflag = 0;

    mutex_exit(&unitp->adm1026_mutex);
    return (DDI_SUCCESS);
}

static int
adm1026_attach(dev_info_t *dip, ddi_attach_cmd_t cmd)
{
    D2CMN_ERR((CE_WARN, "adm1026_attach: cmd=%x\n", cmd));

    switch (cmd) {
    case DDI_ATTACH:
        return (adm1026_do_attach(dip));
    case DDI_RESUME:
        return (adm1026_do_resume());
    default:
        return (DDI_FAILURE);
    }
}

static int
adm1026_detach(dev_info_t *dip, ddi_detach_cmd_t cmd)
{
    D2CMN_ERR((CE_WARN, "adm1026_detach: cmd=%x\n", cmd));
    switch (cmd) {
    case DDI_DETACH:
        return (adm1026_do_detach(dip));
    case DDI_SUSPEND:
        return (adm1026_do_suspend());
    default:
        return (DDI_FAILURE);
    }
}

static int
adm1026_do_attach(dev_info_t *dip)
{
    adm1026_unit_t *unitp;
    int instance;

    instance = ddi_get_instance(dip);

    D2CMN_ERR((CE_WARN, "adm1026_do_attach: instance=%d, dip=%p",
        instance, (void *)dip));

    if (ddi_soft_state_zalloc(adm1026soft_statep, instance) != 0) {
        cmn_err(CE_WARN, "%s%d: ddi_soft_state_zalloc() failed",
            ddi_get_name(dip), instance);
        return (DDI_FAILURE);
    }

    unitp = ddi_get_soft_state(adm1026soft_statep, instance);

    if (unitp == NULL) {
        cmn_err(CE_WARN, "%s%d: ddi_get_soft_state(), no memory",
            ddi_get_name(dip), instance);
        return (ENOMEM);
    }

    D2CMN_ERR((CE_WARN, "adm1026_do_attach: ddi_create_minor_node"));
    if (ddi_create_minor_node(dip, "adm1026", S_IFCHR, instance,
    "ddi_i2c:led_control", NULL) == DDI_FAILURE) {
        cmn_err(CE_WARN,
            "adm1026_do_attach: ddi_create_minor_node failed");
        ddi_soft_state_free(adm1026soft_statep, instance);

        return (DDI_FAILURE);
    }

    D2CMN_ERR((CE_WARN, "adm1026_do_attach: i2c_client_register"));
    if (i2c_client_register(dip, &unitp->adm1026_hdl) != I2C_SUCCESS) {
        ddi_remove_minor_node(dip, NULL);
        ddi_soft_state_free(adm1026soft_statep, instance);
        cmn_err(CE_WARN,
            "adm1026_do_attach: i2c_client_register failed");

        return (DDI_FAILURE);
    }

    mutex_init(&unitp->adm1026_mutex, NULL, MUTEX_DRIVER, NULL);

    D2CMN_ERR((CE_WARN, "adm1026_do_attach: DDI_SUCCESS"));
    return (DDI_SUCCESS);
}

static int
adm1026_do_resume(void)
{
    int ret = DDI_SUCCESS;

    return (ret);
}

static int
adm1026_do_suspend()
{
    int ret = DDI_SUCCESS;

    return (ret);
}

static int
adm1026_do_detach(dev_info_t *dip)
{
    adm1026_unit_t *unitp;
    int instance;

    instance = ddi_get_instance(dip);

    unitp = ddi_get_soft_state(adm1026soft_statep, instance);

    if (unitp == NULL) {
        cmn_err(CE_WARN,
            "adm1026_do_detach: ddi_get_soft_state failed");
        return (ENOMEM);
    }

    i2c_client_unregister(unitp->adm1026_hdl);

    ddi_remove_minor_node(dip, NULL);

    mutex_destroy(&unitp->adm1026_mutex);
    ddi_soft_state_free(adm1026soft_statep, instance);

    return (DDI_SUCCESS);
}

static int
adm1026_get8(adm1026_unit_t *unitp, uint8_t reg, uint8_t *val)
{
    i2c_transfer_t      *i2c_tran_pointer = NULL;
    int         err = DDI_SUCCESS;

    (void) i2c_transfer_alloc(unitp->adm1026_hdl, &i2c_tran_pointer,
        1, 1, I2C_SLEEP);
    if (i2c_tran_pointer == NULL)
        return (ENOMEM);

    i2c_tran_pointer->i2c_flags = I2C_WR_RD;
    i2c_tran_pointer->i2c_wbuf[0] = (uchar_t)reg;
    err = i2c_transfer(unitp->adm1026_hdl, i2c_tran_pointer);
    if (err) {
        D1CMN_ERR((CE_WARN,
            "adm1026_get8: I2C_WR_RD reg=0x%x failed", reg));
    } else {
        *val = i2c_tran_pointer->i2c_rbuf[0];
        D1CMN_ERR((CE_WARN, "adm1026_get8: reg=%02x, val=%02x",
            reg, *val));
    }
    i2c_transfer_free(unitp->adm1026_hdl, i2c_tran_pointer);

    return (err);
}

static int
adm1026_put8(adm1026_unit_t *unitp, uint8_t reg, uint8_t val)
{
    i2c_transfer_t      *i2c_tran_pointer = NULL;
    int         err = DDI_SUCCESS;

    D1CMN_ERR((CE_WARN, "adm1026_put8: reg=%02x, val=%02x\n", reg, val));

    (void) i2c_transfer_alloc(unitp->adm1026_hdl, &i2c_tran_pointer,
        2, 0, I2C_SLEEP);
    if (i2c_tran_pointer == NULL)
        return (ENOMEM);

    i2c_tran_pointer->i2c_flags = I2C_WR;
    i2c_tran_pointer->i2c_wbuf[0] = reg;
    i2c_tran_pointer->i2c_wbuf[1] = val;

    err = i2c_transfer(unitp->adm1026_hdl, i2c_tran_pointer);
    if (err)
        D2CMN_ERR((CE_WARN, "adm1026_put8: return=%x", err));

    i2c_transfer_free(unitp->adm1026_hdl, i2c_tran_pointer);

    return (err);
}

/*
 * adm1026_send8:
 * Read the i2c register, apply the mask to contents so that only
 * bits in mask affected. Or in value and write it back to the i2c register.
 */
static int
adm1026_send8(adm1026_unit_t *unitp, uint8_t reg, uint8_t reg_val,
            uint8_t reg_mask)
{
    uint8_t val = 0;
    int err;

    if ((err = adm1026_get8(unitp, reg, &val)) != I2C_SUCCESS)
        return (err);
    val &= ~reg_mask;
    val |= (reg_val & reg_mask);

    return (adm1026_put8(unitp, reg, val));
}

/*
 * adm1026_set_output:
 * The low 16 bits of the mask is a 1:1 mask indicating which of the
 * 16 GPIO pin(s) to set.
 */
static int
adm1026_set_output(adm1026_unit_t *unitp, uint32_t val, uint32_t mask)
{
    int err = I2C_SUCCESS;

    if (mask & 0xff)
        err = adm1026_send8(unitp, ADM1026_STS_REG5, (uint8_t)val,
            (uint8_t)mask);

    if ((err == I2C_SUCCESS) && (mask & 0xff00))
        err = adm1026_send8(unitp, ADM1026_STS_REG6,
            (uint8_t)(val >> OUTPUT_SHIFT),
            (uint8_t)(mask >> OUTPUT_SHIFT));

    return (err);
}

/*
 * adm1026_get_output:
 * The low 16 bits of the mask is a 1:1 mask indicating which of the
 * 16 GPIO pin(s) to get.
 */
static int
adm1026_get_output(adm1026_unit_t *unitp, uint32_t mask, uint32_t *val)
{
    uint8_t reg_val = 0;
    int err = I2C_SUCCESS;

    if (mask & 0xff) {
        err = adm1026_get8(unitp, ADM1026_STS_REG5, &reg_val);
        if (err != I2C_SUCCESS)
            return (err);

        *val = reg_val;
    }

    if (mask & 0xff00) {
        err = adm1026_get8(unitp, ADM1026_STS_REG6, &reg_val);
        if (err != I2C_SUCCESS)
            return (err);

        *val |= ((reg_val << OUTPUT_SHIFT) & (mask & 0xff00));
    }

    return (err);
}

/*
 * adm1026_set_config:
 * The low 16 bits of the mask is a 1:1 mask indicating which of the
 * 16 GPIO pin(s) to set the polarity or direction configuration for.
 * Each GPIO pin has 2 bits of configuration - 1 polarity bit and 1
 * direction bit.  Traverse the mask 4 bits at a time to determine
 * which of the 4 GPIO Config registers to access and apply the value
 * based on whether cmd is GPIO_SET_CONFIG (set Direction) or
 * GPIO_SET_POLARITY.
 */
static int
adm1026_set_config(adm1026_unit_t *unitp, int cmd, uint32_t val, uint32_t mask)
{
    int i;
    uint8_t r;
    uint32_t m = mask, v = val;
    int err = I2C_SUCCESS;

    for (i = 0, r = ADM1026_GPIO_CFG1; i < BYTES_PER_CONFIG; i++, r++) {
        if (m & GPIO_CFG_MASK) {
            int j;
            uint8_t mm = 0, vv = 0;
            uint8_t bit = (cmd == GPIO_SET_CONFIG) ?
                DIR_BIT : POLARITY_BIT;

            for (j = 0; j < GPIOS_PER_CFG_BYTE; j++) {
                if (m & (1 << j)) {
                    mm |= (bit << (j * BITSPERCFG));
                }
                if (v & (1 << j)) {
                    vv |= (bit << (j * BITSPERCFG));
                }
            }
            D2CMN_ERR((CE_WARN, "adm1026_set_config: r=%02x, "
                "vv=%02x, mm=%02x, m=%02x", r, vv, mm, m));
            err = adm1026_send8(unitp, r, vv, mm);
            if (err != I2C_SUCCESS)
                return (err);
        }
        m >>= GPIOS_PER_CFG_BYTE;
        v >>= GPIOS_PER_CFG_BYTE;
    }
    return (err);
}

/*
 * adm1026_get_config:
 * The low 16 bits of the mask is a 1:1 mask indicating which of the
 * 16 GPIO pin(s) to get the polarity or direction configuration for.
 * Each GPIO pin has 2 bits of configuration - 1 polarity bit and 1
 * direction bit.  Traverse the mask 4 bits at a time to determine
 * which of the 4 GPIO Config registers to access and build the return
 * value based on whether cmd is GPIO_GET_CONFIG (get Direction) or
 * GPIO_GET_POLARITY.
 */
static int
adm1026_get_config(adm1026_unit_t *unitp, int cmd, uint32_t mask, uint32_t *val)
{
    int i, j;
    uint8_t r;
    int err = I2C_SUCCESS;

    *val = 0;

    for (i = 0, r = ADM1026_GPIO_CFG1; i < BYTES_PER_CONFIG; i++, r++) {
        if (mask & GPIO_CFG_MASK) {
            uint8_t newval = 0, x;
            uint8_t bit = (cmd == GPIO_GET_CONFIG) ?
                DIR_BIT : POLARITY_BIT;

            err = adm1026_get8(unitp, r, &x);
            if (err != I2C_SUCCESS)
                return (err);
            for (j = 0; j < GPIOS_PER_CFG_BYTE; j++) {
                if (mask & (1 << j)) {
                    if (x & (bit << (j * BITSPERCFG)))
                        newval |= (1 << j);
                }
            }
            *val |= (newval << (i * GPIOS_PER_CFG_BYTE));
        } else
            *val <<= GPIOS_PER_CFG_BYTE;

        mask >>= GPIOS_PER_CFG_BYTE;
    }
    return (err);
}

static int
adm1026_ioctl(dev_t dev, int cmd, intptr_t arg, int mode, cred_t *credp,
        int *rvalp)
{
    _NOTE(ARGUNUSED(credp, rvalp))

    adm1026_unit_t      *unitp;
    int         instance;
    int         err = DDI_SUCCESS;
    i2c_gpio_t      g_buf;

    instance = getminor(dev);

    D2CMN_ERR((CE_WARN, "adm1026_ioctl: instance=%d, cmd=%x\n",
        instance, cmd));

    unitp = (struct adm1026_unit *)
        ddi_get_soft_state(adm1026soft_statep, instance);

    if (unitp == NULL) {
        cmn_err(CE_WARN, "adm1026_ioctl: ddi_get_soft_state failed");
        err = ENOMEM;
        return (err);
    }

    mutex_enter(&unitp->adm1026_mutex);

    if (ddi_copyin((caddr_t)arg, &g_buf,
        sizeof (i2c_gpio_t), mode) != DDI_SUCCESS) {

        mutex_exit(&unitp->adm1026_mutex);
        return (EFAULT);
    }
    if (g_buf.reg_mask & 0xffff0000) {
        cmn_err(CE_WARN,
            "adm1026_ioctl: reg_mask too large. "
            "Only bits 15-0 supported");
        mutex_exit(&unitp->adm1026_mutex);
        return (EINVAL);
    }
    switch (cmd) {
    case GPIO_SET_OUTPUT:
        err = adm1026_set_output(unitp, g_buf.reg_val, g_buf.reg_mask);
        break;

    case GPIO_GET_OUTPUT:
        err = adm1026_get_output(unitp, g_buf.reg_mask, &g_buf.reg_val);
        if (err == DDI_SUCCESS)
            err = ddi_copyout(&g_buf, (caddr_t)arg,
                sizeof (i2c_gpio_t), mode);
        break;

    case GPIO_SET_CONFIG:
    case GPIO_SET_POLARITY:
        err = adm1026_set_config(unitp, cmd, g_buf.reg_val,
            g_buf.reg_mask);
        break;

    case GPIO_GET_CONFIG:
    case GPIO_GET_POLARITY:
        err = adm1026_get_config(unitp, cmd, g_buf.reg_mask,
            &g_buf.reg_val);
        if (err == DDI_SUCCESS)
            err = ddi_copyout(&g_buf, (caddr_t)arg,
                sizeof (i2c_gpio_t), mode);
        break;
    default:
        D2CMN_ERR((CE_WARN,
            "adm1026_ioctl: Invalid ioctl cmd %x\n", cmd));
        err = EINVAL;
    }
    mutex_exit(&unitp->adm1026_mutex);

    if (err) {
        D2CMN_ERR((CE_WARN,
            "adm1026_ioctl: failed, err=%x\n", err));
        if (err == DDI_FAILURE)
            err = EIO;
    }

    return (err);
}