scsa2usb.conf revision 0167b58cea98965c58fab4be4e690b6e456f7440
#
# CDDL HEADER START
#
# The contents of this file are subject to the terms of the
# Common Development and Distribution License, Version 1.0 only
# (the "License"). You may not use this file except in compliance
# with the License.
#
# You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
# See the License for the specific language governing permissions
# and limitations under the License.
#
# When distributing Covered Code, include this CDDL HEADER in each
# file and include the License file at usr/src/OPENSOLARIS.LICENSE.
# If applicable, add the following below this CDDL HEADER, with the
# fields enclosed by brackets "[]" replaced with your own identifying
# information: Portions Copyright [yyyy] [name of copyright owner]
#
# CDDL HEADER END
#
# Copyright 2006 Sun Microsystems, Inc. All rights reserved.
# Use is subject to license terms.
#
# ident "%Z%%M% %I% %E% SMI"
#
# scsa2usb.conf file
#
# WARNING: This is an UNSTABLE configuration file. Its contents
# may change at any time.
#
# Records in this file may be used to override the vendor-supplied subclass
# and protocol values for USB mass storage devices. Note: only non-class-
# compliant values for subclass and protocol (e.g. 0xff) will be overridden.
# If a device supplies legal, class-compliant values for these fields, those
# values will not be overridden.
#
# Records in this file may also be used to override the default power
# management behavior of USB mass storage devices.
#
# A record in this file has the following format:-
# "vid=vId pid=pId rev=revision subclass=override protocol=override pm=pmvalue
# removable=remvalue modesense=modesensevalue"
#
# where:
# 'prtconf -v' output for the device
#
# vendorId is the hardware property 'usb-vendor-id'
# productId is the hardware property 'usb-product-id'
# revision is the hardware property 'usb-revision-id'
#
# subclass override - could be either "ufi", "scsi", or "atapi"
# where "ufi" -> Device follows UFI transport
# "atapi" -> Device follows ATAPI transport
# "scsi" -> Device follows SCSI transport
#
# These values are part of USB Interface descriptor for that device.
# bInterfaceProtocol type
# 0x1 "scsi"
# 0x2 "atapi"
# 0x4 "ufi"
# 0x5 "atapi"
# 0x6 "scsi"
#
# protocol override - could be either "cbi", "cb", or "bo"
# interrupt pipe status
# "bo" -> Bulk Only device
#
# These values are part of USB Interface descriptor for that device.
# bInterfaceSubClass type
# 0x0 "cbi"
# 0x1 "cb"
# 0x2 "bo" - zip protocol
# 0x50 "bo"
#
# pmvalue - "off" if device is not to be power managed.
# This is the only legal value for this parameter.
# This parameter is included because some devices
# are not capable of being power-managed, i.e. they
# will not respond after having their power lowered.
# If this is the case, the device should have power
# management disabled by setting this to "off".
#
# remvalue - "true" if the device's removable media information
# in its hardware inquiry data is to be overridden. This
# is the only legal value for this parameter.
#
# NOTE: In previous releases, the removable media information
# was always overridden and the only legal value was "false".
#
# There is a removable media status bit in the USB storage
# device's inquiry data to indicate if the device has a media
# that can be removed. Usually only devices like floppy drives
# have this bit set and be called removable media devices.
# Solaris treats removable media devices and non-removable
# media devices differently. Refer to "System Administration
# Guide: Devices and File Systems" - "Using USB Devices
# (Tasks)" - "Using USB Mass Storage Devices" section for
# the differences in system behavior of treating removable
# media devices and non-removable media devices.
#
# By default, Solaris will treat USB storage devices as
# removable media devices depending on the removable media
# bit value. In some cases this may be undesirable and the
# behavior of the previous releases should be preserved. In
# this case the removable media bit value should be overridden.
# By setting "remvalue" to "true", the information provided
# by the device is ignored. Consequently a USB hard disk
# is treated as a removable media disk and will not show in
# format(1M) disk list.
#
# modesensevalue - "false" if the device cannot handle mode sense
# requests. This is the only legal value for this
# parameter. Some devices choke on mode sense requests
# and become unusable.
#
# reduced-cmd-support - "true" if the device cannot handle
# report correct residues on data transfers.
# This is the only legal value for this parameter. This
# setting is recommended for USB memory sticks and USB2.0
# enclosures which may not be USB Mass Storage spec
# compliant.
#
# NOTE: As a special case, "*" may be used as a wildcard which matches
# any field. This is useful in situations where more than one
# vendor produces a particular model of a product, one vendor
# produces more than one product with the same characteristics,
# or a product has more than one revision. The subclass and
# protocol override values may also contain "*" if one or the
# the other does not require an override value.
#
# For the properties to take effect, reboot the system.
#
# To create this list, first COPY the "attribute-override-list =" line
# to the end of the file and uncomment it.
#
# Then COPY sample records and uncomment them or create new records.
# The list consists of one or more records separated by commas and
# terminated by a semicolon.
#
# IMPORTANT: CREATE THE LIST BY ENTERING NEW RECORDS AFTER THE LAST LINE
# OF THE FILE. TO PREVENT CHANGES BEING LOST WHEN THIS FILE IS UPGRADED,
# DO NOT UNCOMMENT LINES "IN PLACE."
#
#attribute-override-list =
#
# for Sony DSC-S85 USB Digital camera:
# "vid=0x54c pid=0x10 rev=* subclass=ufi protocol=cb",
#
# for SanDisk SDDR-05a CF:
# "vid=0x781 pid=1 rev=* subclass=ufi protocol=cb";
#
# to apply to all USB Mass Storage devices:
# "vid=* reduced-cmd-support=true";
#
# well with USB memory sticks)
#
# ANYTHING CHANGED BEFORE THIS POINT MAY BE OVERWRITTEN IN UPGRADE