e1000_phy.h revision 75eba5b6d79ed4d2ce3daf7b2806306b6b69a938
/******************************************************************************
Copyright (c) 2001-2013, Intel Corporation
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice,
this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
3. Neither the name of the Intel Corporation nor the names of its
contributors may be used to endorse or promote products derived from
this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
******************************************************************************/
/*$FreeBSD$*/
#ifndef _E1000_PHY_H_
#define _E1000_PHY_H_
#ifdef __cplusplus
extern "C" {
#endif
#define E1000_MAX_PHY_ADDR 8
/* IGP01E1000 Specific Registers */
#define IGP_PAGE_SHIFT 5
#define PHY_REG_MASK 0x1F
/* GS40G - I210 PHY defines */
#define GS40G_PAGE_SELECT 0x16
#define GS40G_PAGE_SHIFT 16
#define GS40G_OFFSET_MASK 0xFFFF
#define GS40G_PAGE_2 0x20000
#define GS40G_MAC_REG2 0x15
#define GS40G_MAC_LB 0x4140
#define GS40G_MAC_SPEED_1G 0X0006
#define GS40G_COPPER_SPEC 0x0010
#define GS40G_CS_POWER_DOWN 0x0002
#define BM_PORT_CTRL_PAGE 769
#define BM_WUC_PAGE 800
#define BM_WUC_ADDRESS_OPCODE 0x11
#define BM_WUC_DATA_OPCODE 0x12
#define BM_WUC_ENABLE_PAGE BM_PORT_CTRL_PAGE
#define BM_WUC_ENABLE_REG 17
#define PHY_UPPER_SHIFT 21
(((reg) & MAX_PHY_REG_ADDRESS) |\
#define BM_PHY_REG_PAGE(offset) \
#define BM_PHY_REG_NUM(offset) \
#define HV_INTC_FC_PAGE_START 768
#define I82578_ADDR_REG 29
#define I82577_ADDR_REG 16
#define I82577_CFG_REG 22
#define I82577_CTRL_REG 23
/* 82577 specific PHY registers */
#define I82577_PHY_CTRL_2 18
#define I82577_PHY_LBK_CTRL 19
#define I82577_PHY_STATUS_2 26
#define I82577_PHY_DIAG_STATUS 31
/* I82577 PHY Status 2 */
#define I82577_PHY_STATUS2_REV_POLARITY 0x0400
#define I82577_PHY_STATUS2_MDIX 0x0800
#define I82577_PHY_STATUS2_SPEED_MASK 0x0300
#define I82577_PHY_STATUS2_SPEED_1000MBPS 0x0200
/* I82577 PHY Control 2 */
#define I82577_PHY_CTRL2_MANUAL_MDIX 0x0200
#define I82577_PHY_CTRL2_AUTO_MDI_MDIX 0x0400
#define I82577_PHY_CTRL2_MDIX_CFG_MASK 0x0600
/* I82577 PHY Diagnostics Status */
#define I82577_DSTATUS_CABLE_LENGTH 0x03FC
#define I82577_DSTATUS_CABLE_LENGTH_SHIFT 2
/* 82580 PHY Power Management */
#define E1000_82580_PHY_POWER_MGMT 0xE14
/* BM PHY Copper Specific Control 1 */
#define BM_CS_CTRL1 16
/* BM PHY Copper Specific Status */
#define BM_CS_STATUS 17
#define BM_CS_STATUS_LINK_UP 0x0400
#define BM_CS_STATUS_RESOLVED 0x0800
#define BM_CS_STATUS_SPEED_MASK 0xC000
#define BM_CS_STATUS_SPEED_1000 0x8000
/* 82577 Mobile Phy Status Register */
#define HV_M_STATUS 26
#define HV_M_STATUS_AUTONEG_COMPLETE 0x1000
#define HV_M_STATUS_SPEED_MASK 0x0300
#define HV_M_STATUS_SPEED_1000 0x0200
#define HV_M_STATUS_LINK_UP 0x0040
#define IGP01E1000_PHY_PCS_INIT_REG 0x00B4
#define IGP01E1000_PHY_POLARITY_MASK 0x0078
#define IGP01E1000_PSCR_AUTO_MDIX 0x1000
#define IGP01E1000_PSCFR_SMART_SPEED 0x0080
/* Enable flexible speed on link-up */
#define IGP01E1000_GMII_FLEX_SPD 0x0010
#define IGP01E1000_PLHR_SS_DOWNGRADE 0x8000
#define IGP01E1000_PSSR_POLARITY_REVERSED 0x0002
#define IGP01E1000_PSSR_MDIX 0x0800
#define IGP01E1000_PSSR_SPEED_MASK 0xC000
#define IGP01E1000_PSSR_SPEED_1000MBPS 0xC000
#define IGP02E1000_PHY_CHANNEL_NUM 4
#define IGP02E1000_PHY_AGC_A 0x11B1
#define IGP02E1000_PHY_AGC_B 0x12B1
#define IGP02E1000_PHY_AGC_C 0x14B1
#define IGP02E1000_PHY_AGC_D 0x18B1
#define IGP02E1000_AGC_LENGTH_MASK 0x7F
#define IGP02E1000_AGC_RANGE 15
#define E1000_CABLE_LENGTH_UNDEFINED 0xFF
#define E1000_KMRNCTRLSTA_OFFSET 0x001F0000
#define E1000_KMRNCTRLSTA_OFFSET_SHIFT 16
#define E1000_KMRNCTRLSTA_REN 0x00200000
#define E1000_KMRNCTRLSTA_K1_CONFIG 0x7
#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10
/* IFE PHY Extended Status Control */
#define IFE_PESC_POLARITY_REVERSED 0x0100
/* IFE PHY Special Control */
#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010
#define IFE_PSC_FORCE_POLARITY 0x0020
/* IFE PHY Special Control and LED Control */
#define IFE_PSCL_PROBE_MODE 0x0020
/* IFE PHY MDIX Control */
/* SFP modules ID memory locations */
#define E1000_SFF_IDENTIFIER_OFFSET 0x00
#define E1000_SFF_IDENTIFIER_SFF 0x02
#define E1000_SFF_IDENTIFIER_SFP 0x03
#define E1000_SFF_ETH_FLAGS_OFFSET 0x06
/* Flags for SFP modules compatible with ETH up to 1Gb */
struct sfp_e1000_flags {
};
/* Vendor OUIs: format of OUI is 0x[byte0][byte1][byte2][00] */
#define E1000_SFF_VENDOR_OUI_TYCO 0x00407600
#define E1000_SFF_VENDOR_OUI_FTL 0x00906500
#define E1000_SFF_VENDOR_OUI_AVAGO 0x00176A00
#define E1000_SFF_VENDOR_OUI_INTEL 0x001B2100
#ifdef __cplusplus
}
#endif
#endif /* _E1000_PHY_H_ */