bge.conf revision da14cebe459d3275048785f25bd869cb09b5307f
#
# CDDL HEADER START
#
# The contents of this file are subject to the terms of the
# Common Development and Distribution License (the "License").
# You may not use this file except in compliance with the License.
#
# You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
# See the License for the specific language governing permissions
# and limitations under the License.
#
# When distributing Covered Code, include this CDDL HEADER in each
# file and include the License file at usr/src/OPENSOLARIS.LICENSE.
# If applicable, add the following below this CDDL HEADER, with the
# fields enclosed by brackets "[]" replaced with your own identifying
# information: Portions Copyright [yyyy] [name of copyright owner]
#
# CDDL HEADER END
#
#########################################################################
#
# Copyright 2008 Sun Microsystems, Inc. All rights reserved.
# Use is subject to license terms.
#
# Driver.conf file for the BGE driver, for
# Broadcom 579x Gigabit Ethernet devices
#
# All the properties below can be set globally (i.e. for all instances
# of BGE), or on a per-instance basis. See driver.conf(4) for details
# of the syntax of global and per-instance properties.
#
# Properties specified in this file take effect when the driver is first
# loaded, typically just after system boot. Changes to the file will
# therefore not take effect until the next reboot, but will be permanent
# thereafter.
#
# Some of the driver's parameters can also be changed using ndd(1m).
# Changes made with ndd apply only to a specific instance (e.g. bge1).
# They take effect immediately, but are lost if the driver is unloaded.
#
#########################################################################
#
# The autonegotiation feature can be controlled by the boolean properties
# listed below.
#
# Firstly, 'adv_autoneg_cap' controls whether autonegotiation is enabled.
#
# If autonegotiation is turned OFF ("forced mode"), the remaining 'adv_*'
# the first mode found to be enabled, in highest-to-lowest speed order
# (thus, if adv_1000fdx_cap=1, all other values will be ignored; to force
# 10/hdx mode, *all* the faster modes must be explicitly disabled).
#
# BEWARE - it's very easy to end up with a non-working link using forced
# mode. There's NO validation that the link partner actually supports
# the mode that this device has been forced into. In some cases, this
# will prevent the link coming up; in others, the link status will show
# 'up' (electrical connection made) but data transfer will not work at
# all, or will work poorly (low throughput, high collision rates, etc).
#
# Note that many switches *require* autonegotiation in order to operate
# at 1000Mbps or in full-duplex mode or with flow control. In other words,
# the only combinations that are likely to work with autonegotiation off
# are 100Mbps/half-duplex and 10Mbps/half-duplex, unless the peer has also
# been manually forced to some other (matching) combination.
#
# With autonegotiation ON (the default and preferred mode), the 'adv_*'
# properties control which capabilities are advertised to the partner.
# The default is to advertise all the capabilities that the hardware
# supports; thus, the properties below serve only to limit the advertised
# capabilities to restricted subset -- it is not possible to advertise a
# capability that the hardware does not support.
#
# The autonegotiation process will then automagically select the fastest
# partners.
#
# If the local device is set to autonegotiate, but the link partner can't
# or doesn't autonegotiate, the correct speed will be determined anyway,
# and HALF-DUPLEX mode will be selected, as mandated by the IEEE802.3
# standard. This will yield the correct result if the partner is in fact
# incapable of autonegotiating: it must be a half-duplex device, because
# the only devices that don't support autonegotation are half-duplex (the
# standard says that all full-duplex-capable devices must also support
# autonegotiation).
#
# However, this choice will NOT be correct if the peer is actually capable
# of autonegotiation and full-duplex operation, and has been manually set
# to "forced full-duplex without autonegotiation" (a mode not recommended
# by the IEEE standard). The link will appear to work, but the duplex
# mismatch will result in packet loss and spurious "late collisions". In
# such cases, the preferred solution is to enable autonegotiation by the
# peer. Failing that, autonegotiation by the BGE device can be disabled,
# and forced mode used to match the peer's forced settings as above.
#
# adv_autoneg_cap = 1;
# adv_1000fdx_cap = 1;
# adv_1000hdx_cap = 1;
# adv_100T4_cap = 0;
# adv_100fdx_cap = 1;
# adv_100hdx_cap = 1;
# adv_10fdx_cap = 1;
# adv_10hdx_cap = 1;
# adv_asym_pause_cap = 0;
# adv_pause_cap = 0;
#
# All of these parameters can can also be queried and modified at run-time
# by use of the ndd(1m) command.
#
#########################################################################
#
# OBP's device driver exports methods to set the link speed explicity,
# which then pass the information to the Solaris driver through the
# 'transfer-speed' property. It therefore SHOULDN'T be set here, but
# is documented for completeness. If the 'transfer-speed' property is
# set to 10, 100, or 1000, the link will be set to the selected speed,
# and autonegotiation ENABLED but restricted to the specified speed.
# The correct duplex setting will be determined by autonegotiation.
#
# This property, if set, overrides and alters the settings of the adv_*
# parameters corresponding to the properties above.
#
# transfer-speed = 1000;
#
#########################################################################
#
# As a third alternative, the following two properties can be set to
# and alter the settings of the adv_* parameters corresponding to the
# properties above, and take precedence over all other means of setting
#
# Autonegotiation will be DISABLED if EITHER of these properties is set,
# therefore BOTH properties should be set explicity if either one is.
# 'speed' may be set to 10, 100 or 1000, while 'full-duplex' may be 0 or 1.
#
# See the warning above about the potential for misconfiguration when
# autonegotiation is disabled. Defining these properties could leave your
# system configured so that the network will not work at all after reboot,
# requiring manual intervention and further reboots to recover!
#
# speed = 100;
# full-duplex = 0;
#
#########################################################################
#
# with which driver operation is supported. This list will be updated and
# extended as new subsystems are validated ...
#
0x108e1648,
0x108e16a7,
0x108e16a8,
0x17c20010,
0x17341013,
0x101402a6,
0x10f12885,
0x17c20020,
0x10b71006,
0x10280109,
0x102801f8,
0x1028865d,
0x0e11005a,
0x0e1100cb,
0x103c12bc;
#########################################################################
#
# The properties below represents the number of receive and send ring used.
# For BCM5705, BCM5782, etc, there are only 1 receive ring and 1 send ring.
# Otherwise, there can be up to 16 receive rings and 4 send rings.
#