journal-remote: add an example to man

man: revert dynamic paths for split-usr setups This did not really work out as we had hoped. Trying to do this upstream introduced several problems that probably makes it better suited as a downstream patch after all. At any rate, it is not releaseable in the current state, so we at least need to revert this before the release. * by adjusting the path to binaries, but not do the same thing to the search path we end up with inconsistent man-pages. Adjusting the search path too would be quite messy, and it is not at all obvious that this is worth the effort, but at any rate it would have to be done before we could ship this. * this means that distributed man-pages does not make sense as they depend on config options, and for better or worse we are still distributing man pages, so that is something that definitely needs sorting out before we could ship with this patch. * we have long held that split-usr is only minimally supported in order to boot, and something we hope will eventually go away. So before we start adding even more magic/effort in order to make this work nicely, we should probably question if it makes sense at all.

man: generate configured paths in manpages In particular, use /lib/systemd instead of /usr/lib/systemd in distributions like Debian which still have not adopted a /usr merge setup. Use XML entities from man/custom-entities.ent to replace configured paths while doing XSLT processing of the original XML files. There was precedent of some files (such as systemd.generator.xml) which were already using this approach. This addresses most of the (manual) fixes from this patch: http://anonscm.debian.org/cgit/pkg-systemd/systemd.git/tree/debian/patches/Fix-paths-in-man-pages.patch?h=experimental-220 The idea of using generic XML entities was presented here: http://lists.freedesktop.org/archives/systemd-devel/2015-May/032240.html This patch solves almost all the issues, with the exception of: - Path to /bin/mount and /bin/umount. - Generic statements about preference of /lib over /etc. These will be handled separately by follow up patches. Tested: - With default configure settings, ran "make install" to two separate directories and compared the output to confirm they matched exactly. - Used a set of configure flags including $CONFFLAGS from Debian: http://anonscm.debian.org/cgit/pkg-systemd/systemd.git/tree/debian/rules Installed the tree and confirmed the paths use /lib/systemd instead of /usr/lib/systemd and that no other unexpected differences exist. - Confirmed that `make distcheck` still passes.

treewide: Correct typos and spell plural of bus consistent

man: add journal-remote.conf(5)

man: boilerplate unification

man: add emacs header to get correct indention in nxml-mode for the manpage XML files that use 2ch indenting In the long run we really should figure out if we want to stick with 8ch or 2ch indenting, and not continue with half-and-half. For now, just make emacs aware of the files that use 2ch indenting.

docs: remove repeating words from man/*xml

man: add systemd-verify(1)

man: describe new filename rules for journal-remote

man: document systemd-journal-upload

journal-remote: allow splitting incoming logs by source host Previously existing scheme where the file name would be based on the source was just too ugly and unpredicatable. Now there are only two options: 1. just one file (until rotation), 2. one file per source host, using the hostname as filename part. For the cases where the source is specified by the user, only option one is allowed, and the full of the file must be specified.

doc: comma placement corrections and word order Set commas where there should be some. Some improvements to word order.

doc: corrections to words and forms This patch exchange words which are inappropriate for a situation, deletes duplicated words, and adds particles where needed.

journal-remote: implement inheriting http(s) sockets Now --listen-http=-3 --listen-https=-4 can be used to spawn a µhttpd server on those two ports, in http and https modes respectively. As before, --listen-http=3 --listen-https=4 will launch µhttpd servers on ports 3 and 4.

journal-remote: HTTP(s) support The whole tool is made dependent on µhttpd availability. It should be easy to make the µhttpd parts conditional, but since transfer over HTTP seems to be the primary use case, currently this is not done. Current implementation uses nested epoll loops: sd-event is used for the external event loop, and µhttpd uses epoll in its own loop. Unfortunately µhttpd does not expose enough information to add the descriptors it uses to the external event loop. This means that starvation of other events is possible, if one of the inner µhttpd loops is constantly busy. This means that µhttpd servers should not be mixed with other sources. The TLS authentication parts haven't been really tested properly, and should not be take too seriously.

journal-remote: tool to receive messages over the network